MPC564EVB Freescale Semiconductor, MPC564EVB Datasheet - Page 18
![KIT EVAL FOR MPC561/562/563/564](/photos/39/39/393946/mpc564evbimage_sml.jpg)
MPC564EVB
Manufacturer Part Number
MPC564EVB
Description
KIT EVAL FOR MPC561/562/563/564
Manufacturer
Freescale Semiconductor
Type
Microcontrollerr
Specifications of MPC564EVB
Contents
Module Board, Installation Guide, Power Supply, Cable, Software and more
Processor To Be Evaluated
MPC56x
Data Bus Width
32 bit
Interface Type
RS-232, Ethernet
For Use With/related Products
MPC561, 562, 563, 564
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Freescale Semiconductor, Inc.
Support Logic
configuration word IP bit is set to 1. This requires the board to have a non-volatile memory device
in this range with the correct information stored in it. The MPC564 processor chip-select zero
(CS0) responds to any accesses after reset until the OR0 is written. Since CS0 (the global chip
select) is connected to the Flash ROM (U6), the Flash ROM initially appears at address
0xFFF0_0000. The initialization routine then programs the chip-select logic, locates the Flash
ROM to start at 0x0080_0000 and configures the rest of the internal and external peripherals.
Please refer to the MPC561/563 user’s manual (Global (Boot) Chip-Select Operation) for more
information.
1.3 Support Logic
1.3.1 Reset Logic
The reset logic provides system initialization. Reset occurs during power-on or via assertion of the
signal RESET which causes the MPC564 to reset. HRESET is triggered by the reset switch (SW1)
which resets the entire processor/system.
dBUG configures the MPC564 microprocessor internal resources during initialization. The
contents of the exception table are copied to address 0xFFF0_0000 in the SDRAM. The Software
Watchdog Timer is disabled, the Bus Monitor is enabled, and the internal timers are placed in a stop
condition. A memory map for the entire board can be seen in Table 1-1., “The MPC564EVB
Default Memory Map”.
RW0 – 30: External Reset Configuration Word (RCW) Options
RW0, RW2, RW4 – 18, RW23 – 30 provide the user access to external Reset Configuration Word
(RCW) bits not normally required for default MPC564EVB operation. The RW0 – 30 designations
reflect the data bus D0 – D30 bit effected when the RCW word is enabled externally. All RW0 –
30 option bits are defaulted to the logic low value during external RCW word operation. The user
may apply a wire jumper between the 2 pad positions of each RW0 – 30 option to provide a logic
high level on the respective bit position during external RCW operation. Refer to the MPC564 user
manual Reset chapter for the respective RCW bit definitions.
1.3.2 Clock Circuitry
The MPC564EVB board uses a 4MHz crystal (Y1 on the schematics) to provide the clock to the
on-chip oscillator of the MPC564. In addition to the 4MHz crystal, there is also a 25MHz oscillator
(Y3) which feeds the Ethernet chip (U20).
1.3.3 Watchdog Timer
The duration of the Watchdog is selected by the SWT[1:0] bits in the System Protection and
28
Control Register (SYPCR), SWT[1:0] = 0b11 gives a maximum timeout period of 2
/System
frequency. The dBUG monitor initializes these bits with the value 0b11, which provides the
maximum time-out period, but dBUG does NOT enable the watchdog timer via the SYPCR
register SWE bit.
1-8
MPC564EVB User’s Manual
For More Information On This Product,
Go to: www.freescale.com