HS2339KCM01H Renesas Electronics America, HS2339KCM01H Datasheet
HS2339KCM01H
Specifications of HS2339KCM01H
Related parts for HS2339KCM01H
HS2339KCM01H Summary of contents
Page 1
To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...
Page 2
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...
Page 3
... H8S Family E10A Emulator Additional Document for User’s Manual H8S/2339F E10A HS2339KCM01HE-U2 Renesas Microcomputer Development Environment System H8S Family / H8S/2300 Series Specific Guide for the H8S/2339EF, H8S/2329EF, H8S/2319EF E10A Emulator Rev.1.0 2003.10 ...
Page 4
...
Page 5
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...
Page 6
...
Page 7
Section 1 Connecting the Emulator with the User System ............................... 1 1.1 Components of the E10A Emulator .................................................................................. 1 1.2 Connecting the E10A Emulator with the User System .....................................................2 1.3 Pin Assignments of the E10A Connector..........................................................................3 1.4 Example of E10A ...
Page 8
ii ...
Page 9
... Section 1 Connecting the Emulator with the User System 1.1 Components of the E10A Emulator The H8S/2339F E10A emulator supports the H8S/2339EF, H8S/2329EF, and H8S/2319EF. Table 1.1 lists the components of the H8S/2339F E10A emulator. Table 1.1 Components of the E10A Emulator (HS2339KCM01H or HS2339KCI01H) Classi- fication Component Hard- Card emulator ...
Page 10
Connecting the E10A Emulator with the User System Before connecting an E10A emulator with the user system, a connector must be installed in the user system so that an user system interface cable can be connected. When designing the ...
Page 11
Pin Assignments of the E10A Connector Figure 1.2 shows the pin assignments of the H-UDI port connector. Pin 1 mark H-UDI port connector Pin 8 Pin 1 Top view Pin 1 mark Figure 1.2 Pin Assignments of the H-UDI ...
Page 12
Example of E10A Emulator Connection The figure shown below is an example of connecting the user system to the E10A emulator. 14-pin connector with a 2.54-mm pitch (3M Limited: 2514-6002 ...
Page 13
Notes: 1. The emulator uses P34 and P80 to P83 in the H8S/2339EF, P34 and P60 to P63 in the H8S/2329EF, and P20 to P21, P31, P33, and P35 in the H8S/2319EF. Pull up the E10A emulator and MCU pins ...
Page 14
RES# of pin 4 of the H-UDI port connector is a signal line in which the emulator outputs signals to the MCU. RES# of pin 4 and the user system reset circuit must be connected to the MCU, as ...
Page 15
In the H8S/2339, H8S/2329, and H8S/2319 series, only H8S/2339EF, H8S/2329EF, and H8S/2319EF can be connected to the E10A emulator. H8S/2339F, H8S/2329F, and H8S/2319F for general use cannot be used. 8. When H8S/2339EF and H8S/2329EF are connected to the E10A ...
Page 16
8 ...
Page 17
Section 2 Specification of the E10A Emulator’s Software 2.1 Differences between the H8S/2339EF, H8S/2329EF, H8S/2319EF, and the E10A Emulator 1. When the E10A emulator system is initiated, it initializes the general registers and part of the control registers as shown ...
Page 18
... E10A Emulator Driver Selection Table 2.2 shows drivers which can be selected in the [E10A Driver Details] dialog box. Table 2.2 Type Name and Driver Type Name HS2339KCM01H HS2339KCI01H 2.2.2 Hardware Break Functions Hardware Break Conditions: In the H8S/2339F E10A emulator, conditions of Break Condition 1,2 can be set ...
Page 19
Table 2.4 lists the combinations of conditions that can be set in the [Break condition] dialog box. Table 2.4 Conditions Set in [Break condition] Dialog Box Condition Address Bus Dialog Box Condition [Break condition 1] [Break condition 2] Note: O: ...
Page 20
Notes on Setting the Break Condition: 1. When [Go to cursor], [Step In], [Step Over], or [Step Out] is selected, the settings of Break Condition are disabled. 2. The settings of Break Condition are disabled when an instruction to which ...
Page 21
H8S Family E10A Emulator Additional Document for User's Manual Specific Guide for the H8S/2339EF, H8S/2329EF, H8S/2319EF E10A Emulator Publication Date: Rev.1.00, October 6, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department ...
Page 22
Additional Document for User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan H8S Family E10A Emulator REJ10B0033-0100H ...