HW-MP-VO48 Xilinx Inc, HW-MP-VO48 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
HW-MP-VO48
Manufacturer Part Number
HW-MP-VO48
Description
ADAPTER 48-TSOP FLASH PROM
Manufacturer
Xilinx Inc
Datasheet
1.HW-MULTIPRO.pdf
(12 pages)
Specifications of HW-MP-VO48
Accessory Type
Programming Adapter
For Use With/related Products
Xilinx 48-TSOP FLASH PROM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Device Adapters
A separate device adapter is available for each unique
Platform Flash PROM, XC18V00 ISP PROM, and
CoolRunner-II CPLD package. Adapters attach to the
MultiPRO pod using a 20-pin keyed DIN connector
(Figure
during programming operations and removed upon
completion. A power status LED is illuminated whenever
power is active. The MultiPRO pod automatically identifies
any adapter that is attached to the DIN connector.
A polycarbonate label protects the top side of the adapter
printed circuit. Text clearly identifies the device and package
information, the product ordering number, and the index pin
locator needed to orient the device during insertion.
X-Ref Target - Figure 2
Table 1: Status Indicators
DS114 (v1.9) February 8, 2008
Product Specification
Serial/JTAG/SPI
Caution!
from sockets while the ACTIVE LED is illuminated.
Blinking Red
Amber
Amber
Green
2). Power is automatically applied to the adapter
LED
Red
Red
Red
Off
Figure 2: Common Adapter Features
R
Devices should never be installed or removed
DIN Connector
20-pin Keyed
Index Pin Locator
SelectMAP LED
Blinking Red
Amber
Amber
Green
Red
Red
Red
Off
Status LED
Power
Pod Powered
Over-Current
Yes
Yes
Yes
Yes
Yes
Yes
No
www.xilinx.com
An aluminum plate is attached to the bottom side of the
printed circuit board to protect circuitry. Rubber feet are
mounted on the bottom of the aluminum plate to avoid
scratching the desk top.
Over-Current Protection
The MultiPRO Desktop Tool monitors the current load of the
adapter when power is provided. If a fault condition exists
on the adapter (e.g., if a device is improperly oriented in the
socket or the device is internally shorted), power is
automatically shut off. The MultiPRO Desktop Tool will not
be damaged if the power pins on the DIN connector are
inadvertently shorted to ground.
Status Indicators
The MultiPRO Desktop Tool uses tri-color LEDs to indicate
the active configuration port and the presence of target
power
has not been selected in iMPACT. An amber LED indicates
that the port is selected but that V
hardware is not powered. A green LED indicates that the port
is selected and V
If both the Serial/JTAG/SPI and SelectMAP STATUS LEDs
are red, then the Adapter port is active. Power is
automatically switched to adapters only during programming
operations. The adapter’s red ACTIVE LED is illuminated
when power is ON. The MultiPRO Desktop Tool selects the
Serial/JTAG/SPI port by default when powered up.
If both the Serial/JTAG/SPI and SelectMAP LEDs are
blinking red, an over-current condition has been detected on
the adapter port. The adapter should be removed and
checked for incorrect device insertion and/or socket damage.
Active Port
SelectMAP
SelectMAP
Adapter
Adapter
S/JTAG
S/JTAG
(Table
None
None
1). A red LED indicates that the associated port
REF
from the target hardware is powered.
See ACTIVE LED
V
REF
Powered
N/A
Yes
Yes
N/A
N/A
No
No
REF
MultiPRO Desktop Tool
from the target
Parallel Port
Connected
IEEE 1284
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
2