HP-HOLDDOWN-CLIP Panasonic Electric Works, HP-HOLDDOWN-CLIP Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/5/512/panasonic_electric_works_sml.jpg)
HP-HOLDDOWN-CLIP
Manufacturer Part Number
HP-HOLDDOWN-CLIP
Description
ACCY HOLD-DOWN CLIP FOR HP RELAY
Manufacturer
Panasonic Electric Works
Series
HPr
Datasheet
1.HP-HOLDDOWN-CLIP.pdf
(8 pages)
Specifications of HP-HOLDDOWN-CLIP
Accessory Type
Clip, Hold Down
For Use With/related Products
HP Series
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Color
-
2. Specifications
Notes: *1 This value can change due to the switching frequency, environmental conditions and desired reliability level, therefore it is recommended to check this with the
3. Electrical life
1) AC load
Note: When the electromagnet or exciting coil (Solenoid, etc.) is the load, the value of motor or lamp load is applicable.
2) DC load
Note: For DC inductive loads, use an arc suppressing circuit.
Note: Cautions at DC load use
Contact
Rating
Electrical
characteristics
Mechanical
characteristics
Expected life
Conditions
Unit weight
Characteristics
When used under a DC load operating at high repetition rate with considerable arcing, corrosion of the contacts and/or the contact blades is likely to occur.
*2 For the AC coil types, the operate/release time will differ depending on the phase.
*3 The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. Refer to 6. Conditions for operation,
Current
Current
Voltage
Voltage
Load
Load
actual load.
transport and storage mentioned in AMBIENT ENVIRONMENT.
Arrangement
Initial contact resistance, max
Contact material
Nominal switching capacity
Min. switching capacity (Reference value)*
Insulation resistance (Initial)
Breakdown voltage
(Initial)
Temperature rise
Operate time*
Release time*
Shock resistance
Vibration resistance
Mechanical
Conditions for operation, transport and storage*
Max. Operating speed
Resistive (A) (cos =1)
Resistive (A)
2
2
7.5
10
—
—
5
1
5
1
2 Form C, 3 Form C
4 Form C
Between open contacts
Between contact sets
Between contact and coil
Functional
Destructive
Functional
Destructive
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Item
125V AC
24V DC
Inductive (A) (cos =0.4)
Inductive (A)
1
7.5
0.7
0.6
—
3
7
5
3
3
2 Form C, 3 Form C, 4 Form C
Max. 15 m (By voltage drop 6 V DC 1A)
Ag
Ag alloy (cd free)
10A 250V AC (resistive load)
100mA 5V DC
Min. 100M (at 500V DC)
Measurement at same location as “Initial breakdown voltage” section.
1,000 Vrms for 1min (2 Form C, 4 Form C).
2,000 Vrms for 1min (3 Form C) (Detection current: 10mA.)
1,500 Vrms for 1min (2 Form C, 4 Form C).
2,000 Vrms for 1min (3 Form C) (Detection current: 10mA.)
1,500 Vrms for 1min (2 Form C, 4 Form C).
2,000 Vrms for 1min (3 Form C) (Detection current: 10mA.)
Max. 65 C (By temperature method, at 40 C, nominal current)
Max. 25ms (2 Form C), Max.30ms (3 Form C, 4 Form C)
(Nominal voltage applied to the coil, excluding contact bounce time.)
Max. 25ms (2 Form C), Max.30ms (3 Form C, 4 Form C)
(Nominal voltage applied to the coil, excluding contact bounce time.) (without diode)
Min. 98 m/s
Min. 980 m/s
10 to 55 Hz at double amplitude of 1 mm (Detection time: 10 s.)
10 to 55 Hz at double amplitude of 2 mm
Min. 10
Ambient temperature: –50 C to +40 C
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 cpm (at max. rating)
2 Form C: approx. 60g 2.12oz, 3 Form C: approx. 100g 3.53oz, 4 Form C: approx. 125g
7
2
Resistive (A) (cos =1)
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10 s.)
(Half-wave pulse of sine wave: 6 ms.)
Resistive (A)
7.5
0.6
0.5
0.3
0.1
10
—
3
125V DC
250V AC
–58 F to +104 F
Inductive (A) (cos =0.4)
Specifications
Inductive (A)
0.06
7.5
0.4
0.4
0.2
—
5
2
Expected life
Expected life
Min. 2 10
Min. 5 10
Min. 2 10
Min. 2 10
Min. 5 10
Min. 2 10
Min. 10
Min. 10
6
6
5
5
6
5
5
6
4.41oz
HP