SP4-DC12V Panasonic Electric Works, SP4-DC12V Datasheet - Page 7

• Manufacturer Part Number: SP4-DC12V
• Description: RELAY POWER 10A 12VDC PLUG-IN
• Manufacturer: Panasonic Electric Works
• Series: SPr
• Type: Power Relayr

Specifications of SP4-DC12V

• Relay Type: General Purpose
• Contact Form: 4PDT (4 Form C)
• Contact Rating (current): 10A
• Switching Voltage: 250VAC
• Coil Type: Standard
• Coil Current: 25mA
• Coil Voltage: 12VDC
• Turn On Voltage (max): 8.4 VDC
• Turn Off Voltage (min): 1.2 VDC
• Mounting Type: Socket
• Termination Style: Quick Connect - .187" (4.7mm)
• Circuit: 4PDT (4 Form C)
• Contact Rating @ Voltage: 10A @ 250VAC
• Control On Voltage (max): 8.4 VDC
• Control Off Voltage (min): 1.2 VDC
• Relay Construction: Non-Latching
• Contact Arrangement: 4PDT
• Coil Voltage Dc: 12V
• Voltage Rating (vdc): 30V
• Voltage Rating (vac): 250V
• Dropout Volt (min): 1.2VDCV
• Coil Resistance: 480Ohm
• Pick-up Voltage (max): 8.4VDC
• Maximum Power Rating: 300W/2.5KVA
• Operate Time: 30ms
• Contact Current Rating: 10A
• Contact Material: AgSnO2
• Coil Suppression Diode: No
• Push To Test Button: No
• Led Indicator: No
• Seal: Unsealed
• Product Height (mm): 22mm
• Product Depth (mm): 25.6mm
• Product Length (mm): 51mm
• Operating Temp Range: -50C to 60C
• Pin Count: 14
• Mounting Style: Plug-In
• Package / Case: Dust Cover
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 255-2840; SP4-DC12V

SP
Direct chassis mounting possible, and applicable to DIN rail.
DIMENSIONS
Mounting hole diagram
Use method
1. Both the SP relay 2 Form C and
4 Form C can be mounted to the
mounting slats.
2. Use the mounting slats either by
attaching them directly to the chassis, or
by mounting with a DIN rail.
(A) When attaching directly to chassis
Use two M3 screws.
For the mounting pitch, refer to the
specification diagram.
(B) When mounting on a DIN rail
Use a 35mm
(DIN46277).
The mounting method should be as
indicated in the diagram at right.
CAD Data
18.4
.724
Panel cutout
1.378inch
18.4
.724
2.252
57.2
Tolerance: 0.1
(mm inch)
2-3.2 dia. hole
2-.126 dia. hole
wide DIN rail
.984
23.2
.913
25
.004
The CAD data of the products with a
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
Method for mounting on DIN rail
Fit into mounting
grooves.
Press
ACCESSORIES
Press relay in
Fit in
TYPES
CAD Data
Mounting board
To remove the
relay, press down
the mounting slats
so the claws move
to the outside.
Product name
Mounting
slat
DIN rail
Fig. 1
Fig. 2
Fig. 3
mark can be downloaded from: http://panasonic-electric-works.net/ac
(1) First fit the arc shaped claw of the
mounting slat into the DIN rail.
(2) Press on the side as shown in the
diagram below.
(3) Fit in the claw part on the opposite
side.
Precautions for use
When mounting to a DIN rail, use a
commercially available fastening bracket
if there is a need to stop sliding of the
mounting slat in the rail direction.
MOUNTING BOARD
SP RELAYS
Part No.
SP-MA