CB1-T-P-12V Panasonic Electric Works, CB1-T-P-12V Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/5/512/panasonic_electric_works_sml.jpg)
CB1-T-P-12V
Manufacturer Part Number
CB1-T-P-12V
Description
RELAY AUTO 12VDC SEALED PCB
Manufacturer
Panasonic Electric Works
Series
CBr
Datasheet
1.CB1AF-12V.pdf
(11 pages)
Specifications of CB1-T-P-12V
Relay Type
Automotive
Contact Form
SPDT (1 Form C)
Contact Rating (current)
40A
Switching Voltage
12VDC
Coil Type
Standard
Coil Current
117mA
Coil Voltage
12VDC
Turn On Voltage (max)
7 VDC
Turn Off Voltage (min)
1.2 VDC
Mounting Type
Through Hole
Termination Style
PC Pin
Circuit
SPDT (1 Form C)
Contact Rating @ Voltage
40A @ 12VDC
Control On Voltage (max)
7 VDC
Control Off Voltage (min)
1.2 VDC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
CB
5. High contact capacity (1 Form A) (PC board type)
Cautions regarding the protection element
1. Part numbers without protection
elements
1) 12 V models
When connecting a coil surge protection
circuit to these relays, we recommend a
zener diode with a zener voltage of 24 V
or higher, or a resistor (680Ω to 1,000Ω).
When a diode is connected to the coil in
parallel, the release time will slow down
and working life may shorten. Before use,
please check the circuit and verify that
the diode is not connected in parallel to
the coil drive circuit.
2) 24 V models
When connecting a coil surge protection
circuit to these relays, we recommend a
zener diode with a zener voltage of 48 V
or higher, or a resistor (2,800Ω to
4,700Ω).
When a diode is connected to the coil in
parallel, the release time will slow down
and working life may shorten. Before use,
please check the circuit and verify that
the diode is not connected in parallel to
the coil drive circuit.
For Cautions for Use, see Relay Technical Information.
* Intervals between terminals is measured at A surface level.
.209
5.3
2-1.2
2-.047
2-0.8
2-.031
1.004
25.5
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
3-1.7
3-.067
.039
1.0
Sealed by epoxy resin
3.9 3.9
.154 .154
2. Part numbers with diodes
These relays use a diode in the coil surge
protection element. Therefore, the
release time is slower and the working life
might be shorter compared to part
numbers without protection elements and
part numbers with resistors.
Be sure to use only after evaluating under
actual load conditions.
3. Part numbers with resistors
This part number employs a resistor in
the coil surge protection circuit; therefore,
an external surge protection element is
not required. In particular, when a diode
is connected in parallel with a coil, the
release time becomes slower which
could adversely affect working life.
Please check the circuit and make sure
that a diode is not connected in parallel
with the coil drive circuit.
Dimension:
Max. 1mm
1 to 3mm
Min. 3mm
.374
9.5
3
0
8
8
1.043
26.5
6
5
External dimensions
.248
6.3
17.9
.705
.331
8.4
2-2.15
2-.085
.039 to .118
.118
.039
8
7
.039
1.0
4.5
.177
3.9
.154
3.9
.154
inch:
A*
2.6
.102
inch:
.209
8.4
.331
5.3
16.8
.661
.039
1.0
inch: ±0.2
General tolerance
±0.1
±0.3
.374
9.5
22.0
.866
±.004
±.008
±.012
3-1.7
3-.067
4.5
.177
PC board pattern (Bottom view)
3-.071
3-1.8
3-2.15
3-.085
Schematic (Bottom view)
.055
1.4
Including diode type,
including resistor type also available
.307
30
7.8
.102
2.6
30
85
86
86
85
17.9
.705
.331
8.4
87
87
3-2.15
3-.085
3-1.8
3-.071
.307
7.8
.331
8.4
16.8
.661