MC12FD910G-F Cornell Dubilier Electronics (CDE), MC12FD910G-F Datasheet - Page 7
![CAP 91PF 500V MICA CHIP 1210](/photos/25/83/258397/4397465_sml.jpg)
MC12FD910G-F
Manufacturer Part Number
MC12FD910G-F
Description
CAP 91PF 500V MICA CHIP 1210
Manufacturer
Cornell Dubilier Electronics (CDE)
Series
MCr
Datasheet
1.MC08EA220J-TF.pdf
(9 pages)
Specifications of MC12FD910G-F
Package / Case
1210 (3225 Metric)
Capacitance
91pF
Voltage - Rated
500V
Tolerance
±2%
Dielectric Material
Mica
Mounting Type
Surface Mount
Operating Temperature
-55°C ~ 125°C
Features
RF, High Q, Low Loss
Size / Dimension
0.126" L x 0.098" W (3.20mm x 2.50mm)
Height
0.079" (2.00mm)
Leaded Process Compatible
Yes
Termination Type
SMD
Working Voltage, Dc
500V
Capacitance Tolerance
± 2%
Voltage Rating
500V
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Spacing
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Specifications
Quality Factor (Q)
lows when measured at 1 MHz
Insulation Resistance
than 100 GΩ when measured at 100
Vdc
Withstanding voltage
times the rated voltage between 5
seconds and without damage: with
50 mA or less current.
Life Test:
125 ºC ±3 ºC with 1.5 times rated
voltage applied for 2000 (+72, –0)
hours. There will be no visual dam-
age and the capacitors will meet the
limits of the table below.
Vibration Resistance:
the capacitors to simple harmonic
motion with an amplitude of 0.06
inches; vary the frequency uniformly
from 10 to 55 Hz and return to 10 Hz,
all in one minute. Repeat that cycle
continuously for two hours in
After-Test Limits
Vibration Resistance
Capacitance
Solder Heat Res.
Heat Resistance
1 to 80 pF
Moisture Res.
Bending Test
Solderability
>80 pF
Range
Life Test
Test
Subject capacitors to
500 to 3000
Min. Q
Withstand
is as fol-
3000
Voltage
is no less
Subject
IL
IL
IL
IL
IL
IL
is two
Types MC and MCN
Moisture Resistance:
the capacitors to 40 ±2 ºC at 90 to
95% humidity for 500 (+24, –0)
hours. Return to room ambient for
24 hours. There will be no visual
damage and the capacitors will meet
the limits of the table below.
each of three mutually perpendicular
directions. There will be no visual
damage and the capacitors will meet
the limits of the table below.
B
tor as shown below and press the ram
bar until a 2.0 mm deflection is
achieved. There will be no visual
damage and the capacitors will meet
the limits of methods JIS 5102 8.11
and AEC-Q200-005 without crack-
ing or visual damage.
ending Test:
Resistance
Insulation
30 GΩ
30 GΩ
30 GΩ
5 GΩ
IL
IL
7
Mount the capaci-
(whichever >)
Capacitance
IV ±2% or ±.5 pF
IV ±.5% or ±1 pF
IV ±3% or ±.5 pF
IV ±.5% or ±1 pF
IV ±1% or ±1 pF
Subject
IL
Multilayer RF Capacitors
Temperature Coefficient and
Drift:
pacitance at 25 ºC, –55 ºC, 25 ºC, 125
ºC and at 25 ºC — all ±3 ºC — after
stabilizing at each temperature. The
capacitor will meet the limits of the
Characteristic table in Ordering In-
formation.
Heat Resistance:
capacitors to 125 ±2 ºC for 2 (+1,–0)
hours. Then the insulation resistance
will be no less than 5GΩ.
Solderability:
onds in molten solder with Sn-PB
between molten and solder at 235 ±5
ºC, solder coverage will be no less
than 75% when examined at 10X
magnification for flow soldering.
Solder Heat Resistance:
ject the capacitors to molten solder
at 250±5 ºC for 5±0.5 seconds after
10 to 30 seconds pre-heating at 80
to 120 ºC. There will be no visual
damage and the capacitors will meet
the limits of the table below.
Measure the capacitors’ ca-
150% max IL
150% max IL
DF
IL
IL
IL
IL
After 2 ±0.5 sec-
Subject the
2/3 x IL
2/3 x IL
Q
IL
IL
IL
Sub-