LBA110STR Clare, LBA110STR Datasheet
LBA110STR
Specifications of LBA110STR
LBA110STR
Available stocks
Related parts for LBA110STR
LBA110STR Summary of contents
Page 1
... CSA Certified Component: Certificate # 1175739 • EN/IEC 60950-1 Certified Component TUV Certificate 49410 004 Ordering Information Part # LBA110 LBA110S LBA110STR LBA110P LBA110PTR Pin Configuration + Control - Normally Closed – Control - Normally Closed + Control - Normally Open – Control - Normally Open Switching Characteristics of ...
Page 2
... A 150 mW 800 mW 3750 V rms °C °C Conditions Symbol - 10ms I LPK I =120mA =350V LEAK =5mA, V =10V off V =50V, f=1MHz C L OUT I =120mA =5mA = I/O www.clare.com LBA110 Min Typ Max Units - - 120 350 Ω μ 0.4 0 0.9 1.2 1.4 V μ R08 ...
Page 3
... Turn-Off (ms) Form-A Typical I for Switch Dropout F (N=50, I =120mA , T =25º 0.39 0.65 0.91 1.17 1.43 1.69 1.95 LED Current (mA) www.clare.com vs. Temperature I =50mA F I =30mA F I =20mA F I =10mA F I =5mA 100 120 Temperature (ºC) Form-A Typical On-Resistance Distribution (N=50, I ...
Page 4
... Load Voltage (V) Form-A Typical Leakage vs. Temperature Measured Across Pins 5&6 0.016 0.014 0.012 0.010 0.008 0.006 0.004 0.002 0 100 -40 - Temperature (ºC) www.clare.com Form-A Typical I for Switch Operation F vs. Temperature (I =120mA ) L DC 2.5 2.0 1.5 1.0 0 -40 - Temperature (ºC) Form-A Typical Turn-Off vs ...
Page 5
... LED Forward Current (mA) Form-B Typical Turn-On vs. Temperature (I =5mA, I =120mA ) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 100 -40 - Temperature (ºC) www.clare.com Form-B Typical On-Resistance Distribution (N=50, I =5mA, I =120mA , 1.04 25.5 26.5 27.5 28.5 29.5 30.5 On-Resistance (Ω) Form-B Typical Blocking Voltage Distribution (N=50, T =25º ...
Page 6
... Load Voltage (V) Form-B Typical Leakage vs. Temperature Measured Across Pins 5&6 (I =5mA) F 0.016 0.014 0.012 0.010 0.008 0.006 0.004 0.002 0 100 -40 - Temperature (ºC) www.clare.com Form-B Typical Load Current vs. Temperature (I =0mA) F 180 160 140 120 100 -40 - Temperature (ºC) Energy Rating Curve 1.0 ...
Page 7
... Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. ...
Page 8
... PCB Hole Pattern 8-0.800 DIA. 2.540 ± 0.127 (8-0.031 DIA.) (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) 7.620 ± ...
Page 9
... The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc ...