XBA170STR Clare, XBA170STR Datasheet
XBA170STR
Specifications of XBA170STR
XBA170STR
Related parts for XBA170STR
XBA170STR Summary of contents
Page 1
... UL Recognized Component: File E76270 • CSA Certified Component: Certificate 1175739 • EN/IEC 60950-1 Compliant Ordering Information Part # XBA170 XBA170P XBA170PTR XBA170S XBA170STR Pin Configuration + Control - Normally Closed – Control - Normally Closed + Control - Normally Open – Control - Normally Open Switching Characteristics of Normally Open Devices Form ...
Page 2
... V rms °C °C Conditions Symbol Min - I L t=10ms I LPK I =100mA =350V LEAK =5mA, V =10V off V =50V, f=1MHz C L OUT I =100mA 0 =5mA I/O www.clare.com XBA170 Typ Max Units - - 100 350 Ω μ 0 1.2 1.4 V μ R03 ...
Page 3
... Switch Dropout F (N=50, I =100mA , T =25º 0.44 0.50 0.56 0.62 0.69 0.75 0.81 LED Current (mA) www.clare.com XBA170 Typical Leakage vs. Temperature Measured across Pins 5&6 or 7&8 0.016 0.014 0.012 0.010 0.008 0.006 0.004 0.002 0 -40 - 100 Temperature (ºC) FormA Typical On-Resistance Distribution ...
Page 4
... Temperature (ºC) FormA Typical Load Current vs. Load Voltage (I =5mA, T =25º 120 100 -20 -40 -60 -80 -100 -120 - Load Voltage (V) www.clare.com XBA170 Form A Typical Load Current vs. Temperature 160 140 120 100 80 I =20mA =10mA F I =5mA -40 - 100 50 Temperature (ºC) FormA Typical On-Resistance vs ...
Page 5
... Typical Turn-Off vs. Temperature (I =100mA ) L DC 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -40 - 100 120 Temperature (ºC) www.clare.com FormB Typical On-Resistance Distribution (N=50, I =5mA, I =100mA , 1.14 30.59 31.36 32.13 32.90 33.66 34.43 On-Resistance (Ω) FormB Typical Blocking Voltage Distribution (N=50, T =25º ...
Page 6
... Temperature (ºC) FormB Typical Load Current vs. Load Voltage (I =5mA, T =25º 120 100 -20 -40 -60 -80 -100 -120 - Load Voltage (V) www.clare.com XBA170 FormB Typical Blocking Voltage vs. Temperature 455 450 450 440 435 430 425 420 -40 - 100 Temperature (ºC) R03 ...
Page 7
... Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. ...
Page 8
... XBA170 PCB Hole Pattern 8-0.800 DIA. 2.540 ± 0.127 (8-0.031 DIA.) (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± ...
Page 9
... The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc ...