LCC120S Clare, LCC120S Datasheet
LCC120S
Specifications of LCC120S
Available stocks
Related parts for LCC120S
LCC120S Summary of contents
Page 1
... UL Recognized Component: File E76270 • CSA Certified Component: Certificate # 1175739 • EN/IEC 60950-1 Certified Component: TUV Certificate 49410 004 Ordering Information Part # LCC120 LCC120S LCC120STR Pin Configuration AC/DC Configuration 1 Do Not Use 2 + Control 3 – Control 4 Do Not Use Switching Characteristics for a ...
Page 2
... A 150 mW 800 rms +85 ºC +125 ºC Conditions Symbol - I L t=10ms I LPK I =170mA =250V LEAK =10mA, V =10V off V =50V, f=1MHz C L OUT I =170mA =10mA = I/O www.clare.com LCC120 Min Typ Max Units - - 170 400 Ω µ 0.4 0 0.9 1.2 1.4 V μ R08 ...
Page 3
... Typical I for Switch Dropout F (N=50, I =170mA , T =25º 1.05 1.75 2.45 3.15 3.85 4.55 LED Current (mA) www.clare.com Typical Leakage vs. Temperature Measured across Pins 5&6 or 7&8 0.016 0.014 0.012 0.010 0.008 0.006 0.004 0.002 0 120 -40 - Temperature (ºC) 100s Form-A Typical On-Resistance Distribution ...
Page 4
... Load Voltage (V) Form-A Typical Blocking Voltage vs. Temperature 350 345 340 335 330 325 320 315 310 305 -40 - Temperature (ºC) www.clare.com LCC120 Form-A Typical I for Switch Operation F vs. Temperature (I =170mA ) -40 - Temperature (ºC) Form-A Typical Turn-Off vs. Temperature (I =10mA, I =170mA ...
Page 5
... LED Forward Current (mA) Form-B Typical Turn-On vs. Temperature (I =10mA, I =170mA ) 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 100 -40 - Temperature (ºC) www.clare.com Form-B Typical On-Resistance Distribution (N=50, I =10mA, I =170mA , 9.3 10.2 11.1 12.0 12.9 13.8 2.6 On-Resistance (Ω) Form-B Typical Blocking Voltage Distribution (N=50, T =25º ...
Page 6
... Load Voltage (V) Form-B Typical Blocking Voltage vs. Temperature 320 310 300 290 280 270 260 250 240 -40 - Temperature (ºC) www.clare.com Form B Typical Load Current vs. Temperature (I =10mA) F 250 200 150 100 50 0 -40 - Temperature (ºC) 100 LCC120 100 120 R08 ...
Page 7
... This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device LCC120 / LCC120S Board Wash Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes ...
Page 8
... LCC120S Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) Embossed Carrier For additional information please visit our website at: www ...