LD4T06P0 Red Lion Controls, LD4T06P0 Datasheet - Page 10

• Manufacturer Part Number: LD4T06P0
• Description: TIMER 6 DIGIT 4.0" 120VAC RED
• Manufacturer: Red Lion Controls
• Series: LDr
• Type: Timerr

Specifications of LD4T06P0

• No. Of Digits / Alpha: 6
• Digit Height: 101mm
• Power Consumption: 26VA
• Operating Temperature Range: 0°C To +50°C
• Signal Input Type: Pulse
• Character Size: 4"
• Ip/nema Rating: IP65 / NEMA 4X
• Signal Output Type: Relay
• Accuracy: ±0.01% %
• Connection Type: Wire Leads
• Dimensions: 26"L×2.25"W×7.875"H
• Display Digit Height: 4 "
• Display Resolution: 0.001 Sec. (Minimum Digit), 1 hr. (Single Digit)
• Display Type: LED
• Function: Timer
• Material, Casing: Aluminum
• Number Of Digits: 6
• Primary Type: Electronic
• Range, Measurement: 0 to 999999
• Special Features: RS485/RS232 Communications
• Termination: Terminal Block
• Voltage, Supply: 85 to 250/11 to 16 VAC/VDC
• Supply Voltage Range: 21.6V DC To 250V DC
• Count Speed Max: 10Hz
• External Depth: 57.15mm
• External Length / Height: 200mm
• Rohs Compliant: Yes
• Counter Supply Voltage: 85-250VAC/11-16VDC
• Display Font Color: Red
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: RLC125

can activate at a programmed Setpoint Value or can be set to activate when the
Timer starts (
the Setpoint is assigned to the Timer, the value is entered in the same display
format as the selected Timer Range.
On-Off Output mode (
determines when the Setpoint Output will deactivate. The output can be
programmed to deactivate at a Setpoint Off Value or can be set to deactivate
when the Timer starts (
entered. If the Setpoint is assigned to the Timer, the value is entered in the same
display format as the selected Timer Range.
Some parameters will not appear depending on the Setpoint Assignment and
Setpoint Output Action selected.




SPT ACTION DESCRIPTION




5.4 MODULE 4 - S



This parameter determines when the Setpoint output will activate. The output
Selecting
The Setpoint Off parameter only appears if the Setpoint Action is set to
Selecting
Module 4 is the programming module for the Setpoint Output parameters.
Select the display for Setpoint assignment.
This parameter selects the action of the Setpoint output as shown below.




PAR





Assignment
Setpoint




Latched Output Mode
Timed Output Mode
On-Off Output Mode








displays a sub-menu where the Setpoint Value is entered. If

SETPOINT OUTPUT ACTION
displays a sub-menu where the Setpoint Off Value is
) or stops (

SETPOINT ASSIGNMENT


Output Action
Setpoint




SETPOINT OFF





SETPOINT ON
) or stops (



). In this mode, the Setpoint OFF parameter

When Time or Count
When Time or Count
When Time or Count
= Setpoint On value
= Setpoint On value

OUTPUT ACTIVATES
Setpoint On value
to
).
to
Setpoint On




).
ETPOINT
Setpoint Off
OUTPUT DEACTIVATES
When Time or Count

(if
At Manual Reset
Output Time-Out
Setpoint Off value

After Setpoint
PARAMETER MENU
=

Time-out
O
Setpoint
Output
)
UTPUT
10

(
activated. This value is always entered in minutes, seconds, and hundredths of
seconds format. The maximum value is 99 minutes 59.99 seconds.
(
Start edge is applied on the Timer input.
Output activates (
not cause a display reset.




powered down.
output at power up. This parameter is not active when the Setpoint Action is
selected for timed output mode.


Assigned display resets. Reset can occur by the RST key or the User Input,
if programmed for that function. Select
reset when the display resets.





Stop Timer
This parameter is only active if the Setpoint Action is set to Timed Output mode
Stops the Timer when the Setpoint output activates (
The Timer Stop condition is cleared when a Timer Reset occurs, or a Time
Automatically resets the Setpoint Assigned display value when the Setpoint

Select
SETPOINT OUTPUT RESET WITH DISPLAY RESET
    
). Enter the time duration the Setpoint Output will remain ON once it is
). Select
P
will restore the output to the same state it was at before the meter was

ARAMETERS
SETPOINT OUTPUT POWER-UP STATE
to have the Setpoint Output deactivate (reset) when the Setpoint



Timer/Counter



Auto Reset





TIMER/COUNTER AUTO RESET

SETPOINT OUTPUT TIME-OUT
will activate the output at power up.
if the output should not affect the Timer Run/Stop status.
) or deactivates (
    



STOP TIMER


Output Reset
with Display
Setpoint



Reset


to
(

    



if the Setpoint output should not
). Select
Power-up
Setpoint
Output
State
)



if the output should
will deactivate the
) or deactivates