I3000S FLEX-24 Fluke Electronics, I3000S FLEX-24 Datasheet

no-image

I3000S FLEX-24

Manufacturer Part Number
I3000S FLEX-24
Description
CLAMP CURRENT AC 24IN 3000AMP
Manufacturer
Fluke Electronics
Type
AC Clampr
Datasheets
1.I2000_FLEX.pdf (10 pages)
2.I3000S_FLEX-24.pdf (2 pages)

Specifications of I3000S FLEX-24

Style
Flexible Ring
Ac Current Range
30 ~ 3000A rms
Bandwidth
50kHz
Cable Length
78.740" (2000.00mm)
Max Conductor Size
7.000" (177.80mm)
Termination
BNC
Ratings
CAT III 600V
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
2584888
Introduction
The i3000s 24 Flex, i3000s 36 Flex, and i2000 Flex AC Current
Probes (hereafter referred to as “the Probe”) are used with
oscilloscopes, digital multimeters, recorders or data loggers. The
i3000s probes can be used to measure AC current up to 3000 A.
The i2000 can be used to measure AC current up to 2000 A. The
flexible measuring head allows current measurements on
conductors that are hard to reach or inaccessible using typical
clamp-on current probes.
The Probes provide a low-voltage (3 V AC for i3000s models,
and 2 V AC for i2000) output that is proportional to the current
being measured. The Probes provide full-scale direct readings for
30 A, 300 A, and 3000 A when using the i3000s models, and 20
A, 200 A, and 2000 A when using the i2000.
Symbols
The following table shows the symbols used on the product
and/or in this manual.
PN 2560447
March 2006
©2006 Fluke Corporation. All rights reserved.
Symbol
>
W
P
-
T
~
Do not dispose of this product as unsorted municipal
waste. Contact Fluke or a qualified recycler for
disposal.
Important Information. Refer to the manual.
Double/Reinforced insulation.
Do not apply around or remove from the HAZARDOUS
LIVE conductors.
Complies with the relevant European standards.
Conforms to Underwriters’ Laboratory, Inc.
i3000s/i2000 Flex
AC Current Probe
Description
Instruction Sheet
®

I3000S FLEX-24 Summary of contents

Page 1

Flex Introduction The i3000s 24 Flex, i3000s 36 Flex, and i2000 Flex AC Current Probes (hereafter referred to as “the Probe”) are used with oscilloscopes, digital multimeters, recorders or data loggers. The i3000s probes can be used to measure ...

Page 2

Safety Instructions In this instruction sheet, a Warning identifies conditions and actions that pose hazard(s) to the user. A Caution identifies conditions and actions that may damage the calibrator or the test instruments. To avoid electric shock or personal injury: ...

Page 3

Adhere to local and national safety codes. Individual protective equipment must be used to prevent shock and arc blast injury where hazardous live conductors are exposed. CAT III equipment is designed to protect against the transients in the equipment in ...

Page 4

Gain variation Operating temperature i3000s (24 and 36 Flex) i2000 Flex Storage temperature i3000s (24 and 36 Flex) i2000 Flex Temperature coefficient: Operating humidity: Altitude: Power supply Battery life i3000s (24 and 36 Flex) i2000 Flex Low battery General Characteristics ...

Page 5

Measuring Head Characteristics Cable length i2000, i3000s 24 Flex i3000s 36 Flex Cable diameter Bend radius Output cable Coupling diameter Material Operating temperature Storage temperature Maximum relative humidity Weight Safety 610 mm (24 in), double insulated 915 mm (36 in), ...

Page 6

Operating Instructions Measuring head A Measuring head coupling B Head output cable C Enclosure D Power on/Range selector E Battery low indicator F Power on indicator G Output cable H Safety BNC connector I External power supply input J Ieb0001.eps ...

Page 7

Battery Installation To avoid electric shock or personal injury: Never replace batteries with the flexible measuring head installed on the conductor to be tested or with the output connected to a display device. Never operate the unit without the battery ...

Page 8

Measuring Current To avoid electric shock or injury, read Safety Instructions before operating this product Ensure that the conductor to be tested is de- energized To measure current: 1. Connect the output of the electronics to the input of an ...

Page 9

Operation To activate the unit, move the switch from ‘Off’ position to the required measuring range. If the value of current being measured is unknown, select the 3000 A (i3000s models) or 2000 A (i2000) current range and then reduce ...

Page 10

LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, ...