90547-1 Tyco Electronics, 90547-1 Datasheet - Page 3

• Manufacturer Part Number: 90547-1
• Description: ASSY PRO-CRIMPER UNIV M-N-L
• Manufacturer: Tyco Electronics
• Series: Pro-Crimper™ III, Universal MATE-N-LOK®r
• Type: Hand Toolr

Specifications of 90547-1

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Crimp Tool: Hand Crimper III
• Product: Crimping, Stripping & Cutting Tools & Drills
• For Use With: 926902-3 - CONN SPLIT PIN 13-15AWG GOLD926901-3 - CONN PIN 13.15AWG TIN CRIMP TERM926900-1 - CONN PIN 13.5-15.5AWG TIN CRIMP926900-3 - CONN PIN 13.5-15.5AWG TIN CRIMP926902-1 - CONN SPLIT PIN 13-15AWG TIN926901-1 - CONN SOCKET 13.15AWG TIN CRIMPA31711 - CONN SOCKET 14-20AWG GOLD CRIMPA31710 - CONN PIN 14-20AWG GOLD CRIMPA25738 - CONN PIN 14-20AWG GOLD CRIMPA25737 - CONN PIN 14-20AWG TIN CRIMPA25408 - CONN PIN 14-20AWG GOLD CRIMPA25371 - CONN PIN 14-20AWG GOLD CRIMPA25374 - CONN PIN 14-20AWG TIN CRIMPA25368 - CONN PIN 14-20AWG GOLD CRIMPA14303 - CONN PIN 14-20AWG TIN CRIMPA14267 - CONN SOCKET 14-20AWG GOLD CRIMPA14266 - CONN SOCKET 14-20AWG TIN CRIMPA14259 - CONN PIN 14-20AWG GOLD CRIMPA14258 - CONN PIN 14-20AWG TIN CRIMP
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 14-20 AWG
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 90547-1; A25161

Rev D
Adjustment
Screw for
Contact
Support
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
i
Contact
Support
The ratchet has detents that create audible clicks
as the tool handles are closed.
Locator
Figure 3
Back of Tool
(Wire Side
5. CRIMPING PROCEDURE
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
Wire
NOTE
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
i
Contact
(Typ)
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION, and
Section 7, RATCHET (Crimp Height)
ADJUSTMENT, to verify crimp height before
using the tool to crimp desired contacts and wire
sizes.
Locator in
Wire Stop
Slot
Strip
Length
Wire
Inserted
to Stop
408- 9883
3 of 6