63819-1300 Molex Inc, 63819-1300 Datasheet - Page 5

• Manufacturer Part Number: 63819-1300
• Description: TOOL HAND CRIMP 18-24AWG RATCHET
• Manufacturer: Molex Inc
• Series: PremiumGrade™r

Specifications of 63819-1300

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Product: Crimping, Stripping & Cutting Tools & Drills
• Fits Cable/wire: 24-18 AWG
• Rohs Compliant: NA
• Wire Size (awg): 24-18
• Lead Free Status / RoHS Status: Lead free by exemption / RoHS compliant by exemption
• For Use With/related Products: Rectangular Contacts, 18-24 AWG
• For Use With: WM1008CT - CONN TERM FEMALE 18-24AWG GOLDWM1008TR - CONN TERM FEMALE 18-24AWG GOLD0002061101 - CONN TERM FEMALE 18-24AWG TINWM3680TR - CONN TERM MALE 18-24AWG TIN02-06-5102 - CONN TERM FEMALE 18-24AWG GOLD02-06-6102 - CONN TERM MALE 18-24AWG GOLDWM1008 - CONN TERM FEMALE 18-24AWG GOLDWM1006 - CONN TERM MALE 18-24AWG GOLDWM1001 - CONN TERM FEMALE 18-24AWG TINWM1000 - CONN TERM MALE 18-24AWG TIN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 063819-1300; 063819-1300-P; 0638191300; 0638191300-P; 63819-1300-P; 638191300; 638191300-P; WM9025

Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals
Doc No: ATS-638191300
Revision: A
SQUEEZE
8. Remove the crimped terminal from the terminal
9. Visually inspect the crimped terminal for proper
10. On some large O.D. wires, it may not be possible
Note:
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers available, actual crimp height measurements may very slightly. An
occasional, destructive, pull force test should be preformed to check hand tool crimp. Pull Force value Must exceed
the Minimum pull force specifications listed.
Locator Replacement
See the parts list on the last page of this document for the proper locator order number. Follow the steps below to
replace the locator.
1. Open the crimp hand tool.
2. Squeeze gently on the lower area shown in Figure 7A with your thumb and index finger. The lower tabs of the
3. Lift and pull away from the hand tool. The top locator hooks should slip out of the top slots easily. See Figure
HERE
locator by pulling on the wire.
crimp location.
to insert the wire with the tool partially closed.
Those wires should be inserted with the hand tool
in the open position. Insert the wire above the
terminal in the punch and against the wire stop
then close the tool. See Figure 6.
locator should disengage from the hand tool.
7A.
LOWER TABS
LOCATOR
TOP SLOTS OF
TOP HOOKS
HANDTOOL
Release Date: 01-22-08
Revision Date: 01-22-08
Figure 7A
SQUEEZE
HERE
CENTER OF LOCATOR
DOWN POSITION
MAKE SURE
IS IN THE
Figure 7B
UNCONTROLLED COPY
M3 BHCS
TOOLING
Figure 8
PULL OPEN
JAWS OPEN
PUSH ON
HANDLE
TERMINAL
WIRE STOP
Figure 6
WIRE
Page 5 of 9
TOOLING