64001-0900 Molex Inc, 64001-0900 Datasheet - Page 4
![TOOL CRIMP SPLICE 12-22AWG](/photos/9/85/98593/64001-0900_sml.jpg)
64001-0900
Manufacturer Part Number
64001-0900
Description
TOOL CRIMP SPLICE 12-22AWG
Manufacturer
Molex Inc
Type
Hand Crimp Toolr
Datasheets
1.64016-0201.pdf
(1 pages)
2.19284-0034.pdf
(27 pages)
3.64001-0900.pdf
(7 pages)
4.64001-0900.pdf
(1 pages)
Specifications of 64001-0900
Features
Side Entry, Ratchet
Tool Type
Hand Crimper
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Tool for crimping terminals
Fits Cable/wire
22-12 AWG
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
Splices, 12-22 AWG
For Use With
WM18394 - CONN SPLICE CLOSED END 12-22AWG
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
064001-0900
064001-0900-E
0640010900
0640010900-E
64001-0900-E
640010900
640010900-E
WM9977
064001-0900-E
0640010900
0640010900-E
64001-0900-E
640010900
640010900-E
WM9977
RHT7050 Hand Crimp Tool
Doc No. 64001-0900
Revision: D
Maintenance
It is recommended that each operator of the tool be made aware of,
and responsible for, the following maintenance steps:
1. Remove dust, moisture and other contaminants with a clean
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are
4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position,
open easily by pressing the ratchet release lever (See Figure 5).
How To Adjust Tool Preload
It may be necessary over the life of the tool to adjust tool handle preload force. Listed below are the steps required to adjust the
crimping force of the hand tool to obtain proper crimp conditions:
1. Remove the screw and plastic cover washer.
2. Lift the setting wheel off the axle. Turn the
3. Turning the eccentric axle counter-clockwise
4. Replace the setting wheel to the axle, aligning
5. Replace the plastic cover washer and screw.
6. Check the crimp specifications after tool
brush, or soft, lint-free cloth.
protected with a thin coat of high quality machine oil. Do not oil
excessively. The 64001-0900 (RHT-7050) was engineered for
durability, but like any fine piece of equipment it needs cleaning
and lubrication for a maximum service life of trouble-free
crimping. A light oil, such as 30 weight automotive oil used at the oil points shown in Figure 4, every 5,000 crimps or 3 months
will significantly enhance the tool life and ensure a stable calibration.
in a clean, dry area.
Note the setting wheel position.
eccentric axle with a screwdriver.
(CCW) will increase handle force.
the nearest notch in the setting wheel to the
dowel pin.
handle preload force is adjusted.
Release Date: 10-09-02
Revision Date: 05-11-05
(See Figure 5)
UNCONTROLLED COPY
RELEASE LEVER
RATCHET
PUSH UP
Do Not force the handles open or
Figure 4
LOCKING SCREW
ADJUSTMENT
PRELOAD
TEST POINT
PRELOAD
TEST POINT
PRELOAD
LUBRICATION POINTS
LIGHT OIL (EVERY
5,000 CRIMPS)
3 MONTHS OR
(BOTH SIDES)
closed. The tool will
Figure 5
1.00
Page 4 of 7
1.00