64001-4500 Molex Inc, 64001-4500 Datasheet - Page 3
![TOOL CRIMP SEALED 14-22AWG .250](/photos/9/85/98594/64001-4500_sml.jpg)
64001-4500
Manufacturer Part Number
64001-4500
Description
TOOL CRIMP SEALED 14-22AWG .250
Manufacturer
Molex Inc
Series
Perma-Seal™r
Specifications of 64001-4500
Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Quick Connects Terminals and Splices, 10-22 AWG
For Use With
WM2964 - CONN SPLICE BUTT 14/16-18/22AWGWM18950 - CONN SPLICE BUTT 10/12-14/16AWGWM18431 - CONN .250"FEMALE SEALED 14-16AWGWM18430 - CONN .250"MALE SEALED 14-16AWGWM18429 - CONN .250"FEMALE SEALED 18-22AWGWM18428 - CONN .250"MALE SEALED 18-22AWG
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
064001-4500
064001-4500-E
0640014500
0640014500-E
64001-4500-E
640014500
640014500-E
WM9976
064001-4500-E
0640014500
0640014500-E
64001-4500-E
640014500
640014500-E
WM9976
RHT-5771 Hand Crimp Tool
Doc No. 64001-4500
Revision: B
7. Remove the crimp and inspect for proper crimp. Molex offers a Crimp Inspection Handbook for closed barrel industrial product.
Crimping Butt Splices
When crimping butt splices, the locator must be removed.
1. Position the splice into the proper color-coded nest.
2. Partially close the tool to hold the splice in place.
3. Insert the properly stripped wire into the splice. The wires end
4. Remove the crimped splice. Inspect for proper crimp location.
5. Rotate the butt splice terminal 180°, so that the opposite end of
6. Repeat steps 2 thru 4.
Note: Whenever crimping without the locator, make sure the seam of the terminal is oriented up or down in the tool if using
unbrazed product, as this will provide higher pull force values.
Maintenance
It is recommended that each operator of the tool be made aware
of, and responsible for, the following maintenance steps:
1. Remove dust, moisture and other contaminants with a clean
2. Do not use any abrasive materials that could damage the
3. Make certain all pins; pivot points and bearing surfaces are
4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position,
open easily by pressing the ratchet release lever, (See Figure 6).
See our website or contact your sales engineer.
should butt against the tab in the terminal (See Figure 4). Cycle the
tool.
splice is in the nest.
brush, or soft, lint-free cloth.
tool.
protected with a thin coat of high quality machine oil. Do not
oil excessively. The 64001-4500 (RHT-5771) was
engineered for durability, but like any fine piece of
equipment, it needs cleaning and lubrication for a maximum
service life of trouble-free crimping. A light oil, such as 30
weight automotive oil used at the oil points shown in Figure 5, every 5,000 crimps or 3 months will significantly enhance the tool
life and ensure a stable calibration.
a clean, dry area.
Release Date: 11-06-03
Revision Date: 07-05-06
UNCONTROLLED COPY
Do Not force the handles open or
STEP DOWN BUTT
SPLICE TERMINAL
TERMINAL
TAB OF
Figure 5
Figure 4
(BOTH SIDES) LIGHT OIL
closed. The tool will
(EVERY 3 MONTHS OR
CONDUCTOR
LUBRICATION POINTS
ANVIL
5,000 CRIMPS)
CONDUCTOR
PUNCH
Page 3 of 6
WIRE