63811-7900 Molex Inc, 63811-7900 Datasheet
![TOOL HAND CRIMP 28-32AWG 1.25MM](/photos/9/86/98602/63811-7900_sml.jpg)
63811-7900
Specifications of 63811-7900
063811-7900-E
0638117900
0638117900-E
63811-7900-E
638117900
638117900-E
WM9805
63811-7900 Summary of contents
Page 1
... The above terminal drawing is a generic terminal representation not an image of a terminal listed in the scope. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 HAND CRIMP TOOL Specification Sheet Order No. 63811-7900 Wire Size Reel AWG mm² 30-32 0.05-0.03 0.40-0.55 .016-.022 1.30-1.70 .051-.067 CONDUCTOR BELL MOUTH ...
Page 2
... While holding the locator button in, load the terminal into the proper nest opening in the locator based on the wire gauge or terminal type markings on the hand tooling. See Figure 3. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 Conductor Crimp Insulation Crimp Height (Ref.) Width (Ref ...
Page 3
... On some large O.D. wires, it may not be possible to insert the wire with the tool partially closed. Those wires should be inserted with the hand tool in the open position. Insert the wire above the terminal in the punch and against the wire stop then close the tool. See Figure 6. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B ...
Page 4
... Rotate the locator down and press the lower tabs into the two bottom slots of the hand tool. To secure the locator into place, the lower tabs must snap into place on the hand tool frame. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 ...
Page 5
... Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. pressing up on the ratchet release lever in the movable handle. See Figure 11. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 FRONT ...
Page 6
... Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 ...
Page 7
... If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 ...
Page 8
... Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan 1-800-78MOLEX 81-462-65-2324 amerinfo@molex.com feninfo@molex.com Doc No: ATS-638117900 Release Date: 05-31-07 Revision: B Revision Date: 04-28-08 Order Number Description 63811-7900 Hand Crimp Tool 63811-7975 Locator Assembly 63810-0104 Spring, Return 63810-0105 Spring, Ratchet 2 Figure 13 Far East South Headquarters European Headquarters ...