63819-0800 Molex Inc, 63819-0800 Datasheet - Page 5

• Manufacturer Part Number: 63819-0800
• Description: TOOL HAND CRIMP 22-30AWG
• Manufacturer: Molex Inc
• Series: PremiumGrade™, KK®, Spox™r
• Type: Crimp Toolr

Specifications of 63819-0800

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Product: Crimping, Stripping & Cutting Tools & Drills
• Description/function: Crimp Tool
• Rohs Compliant: NA
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 22-30 AWG
• For Use With: WM23941CT - CONN TERM CRIMP 22-30AWG GOLDWM1003CT - CONN TERM FEMALE 24-30AWG TINWM23941TR - CONN TERM CRIMP 22-30AWG GOLDWM1003TR - CONN TERM FEMALE 24-30AWG TINWM2755CT - CONN TERM 24-30AWG HI PRESS TINWM2755TR - CONN TERM 24-30AWG HI PRESS TINWM1009 - CONN TERM FEMALE 24-30AWG GOLDWM1007 - CONN TERM MALE 24-30AWG GOLDWM2612 - CONN TERM 24-30AWG HI PRESS TINWM23941 - CONN TERM CRIMP 22-30AWG GOLDWM1003 - CONN TERM FEMALE 24-30AWG TINWM1002 - CONN TERM MALE 24-30AWG TIN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 063819-0800; 063819-0800-P; 0638190800; 0638190800-P; 63819-0800; 63819-0800-P; 638190800; 638190800-P; Q3830189; WM9021

Hand Crimp Tool For .062” Pin and Socket, SPOX™ and KK® High Pressure Crimp Terminals
Doc No: ATS-638190800
Revision: B
8. Remove the crimped terminal from the terminal
9. Visually inspect the crimped terminal for proper
10. On some large O.D. wires, it may not be possible to
Note:
A crimp height chart is provided with this manual
as Reference Only. Due to the wide range of
wires, strands, insulation diameters, and
durometers available, actual crimp height
measurements may very slightly. An occasional,
destructive, pull force test should be performed to
check hand tool crimp. Pull Force value Must
exceed the Minimum pull force specifications listed.
Locator Replacement
See the parts list on the last page of this document
for the proper locator order number. Follow the
steps below to replace the locator.
1. Open the crimp hand tool.
2. Squeeze gently on the lower area shown in
3. Lift and pull away from the hand tool. The top
4. To reinstall the new locator, make sure the hand
5. Press the red insert down as far as it will go as
6. Holding onto the lower part of the locator with your
7. Rotate the locator down and press the lower tabs
locator by pulling on the wire.
crimp location.
insert the wire with the tool partially closed. Those
wires should be inserted with the hand tool in the
open position. Insert the wire above the terminal in
the punch and against the wire stop then close the
tool. See Figure 6.
Figure 7A with your thumb and index finger.
The lower tabs of the locator should disengage
from the hand tool.
locator hooks should slip out of the top slots easily.
See Figure 7A.
tool is in the open position.
shown in Figure 7B.
thumb and index finger, insert the locators top
hooks (2) into the hand tool top slots.
into the two bottom slots of the hand tool. To
secure the locator into place, the lower tabs must
snap into place on the hand tool frame.
Release Date: 10-25-07
Revision Date: 03-09-08
SQUEEZE
HERE
UNCONTROLLED COPY
M3 BHCS
Figure 7A
TOOLING
LOWER TABS
Figure 11
LOCATOR
PULL OPEN
TOP SLOTS OF
TOP HOOKS
HANDTOOL
JAWS OPEN
PUSH ON
HANDLE
TERMINAL
WIRE STOP
SQUEEZE
Figure 6
WIRE
HERE
CENTER OF LOCATOR
DOWN POSITION
MAKE SURE
Figure 7B
IS IN THE
Page 5 of 9
TOOLING