91506-1 Tyco Electronics, 91506-1 Datasheet - Page 4

• Manufacturer Part Number: 91506-1
• Description: TOOL CERTICRIMP 14-16AWG UMNL
• Manufacturer: Tyco Electronics
• Series: Certi-Crimp™ II, Universal MATE-N-LOK®r
• Type: Crimp Toolr

Specifications of 91506-1

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Rohs Compliant: NA
• Product: Crimping, Stripping & Cutting Tools & Drills
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 14-16 AWG
• For Use With: A31711 - CONN SOCKET 14-20AWG GOLD CRIMPA31710 - CONN PIN 14-20AWG GOLD CRIMPA25738 - CONN PIN 14-20AWG GOLD CRIMPA25737 - CONN PIN 14-20AWG TIN CRIMPA25730 - CONN PIN 14-20AWG GOLD CRIMPA25694 - CONN PIN 14-20AWG GOLD CRIMPA25409 - CONN SOCKET 14-20AWG GOLD CRIMPA25408 - CONN PIN 14-20AWG GOLD CRIMPA25371 - CONN PIN 14-20AWG GOLD CRIMPA25374 - CONN PIN 14-20AWG TIN CRIMPA25372 - CONN SOCKET 14-20AWG GOLD CRIMPA25375 - CONN SOCKET 14-20AWG TIN CRIMPA25369 - CONN SOCKET 14-20AWG GOLD CRIMPA25381 - CONN SOCKET 14-18AWG TIN CRIMPA25380 - CONN PIN 14-18AWG TIN CRIMPA25338 - CONN PIN 14-20AWG TIN CRIMPA25368 - CONN PIN 14-20AWG GOLD CRIMPA14303 - CONN PIN 14-20AWG TIN CRIMPA14302 - CONN SOCKET 14-20AWG TIN CRIMPA14267 - CONN SOCKET 14-20AWG GOLD CRIMPA14266 - CONN SOCKET 14-20AWG TIN CRIMPA14259 - CONN PIN 14-20AWG GOLD CRIMPA14258 - CONN PIN 14-20AWG TIN CRIMP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A9946

4.5. CERTI-CRIMP Ratchet Inspection
The CERTI–CRIMP ratchet feature on these hand tools
should be checked to ensure that the ratchet does not
release prematurely, allowing the crimping dies to open
before they have fully bottomed. Obtain a 0.025–mm
[.001–in.] shim that is suitable for checking the clearance
between the bottoming surfaces of the crimping dies.
Proceed as follows:
CERTI-CRIMP II Straight Action Hand Tools
50.04
[1.970]
4
of 4
1. Select the maximum size wire and strip it
according to dimensions listed in the drawing shipped
with the tool.
2. Select contact and crimp section corresponding to
the selected wire size (refer to the drawing shipped
with the tool).
3. Position the contact and wire in the crimping dies,
as described in the CRIMPING PROCEDURE
section.
4. Hold the wire in place and squeeze the handles
until the CERTI–CRIMP ratchet releases. Hold the
handles in this position, maintaining just enough
tension to keep the dies closed.
5. Check the clearance between the bottoming
surfaces of the wire crimper and the wire anvil. See
Figure 1. If the clearance is 0.025 mm [.001 in.] or
less (on at least two of the bottoming surfaces), the
ratchet is satisfactory. If clearance exceeds 0.025 mm
[.001 in.], the ratchet is out of adjustment and must be
repaired. See Section 5.
29.46 [1.160]
ITEM
1
19.81 [.780]
41.91 [1.650]
12.19 [.480]
76.71 [3.020]
PART NUMBER
21045-3
1
D
Closed to Last Ratchet Point Before Release
Tyco Electronics Corporation
REPLACEABLE PARTS
296.93 [11.690]
Figure 4
5. REPLACEMENT AND REPAIR
Replacement parts are listed in Figure 4. Parts other
than those listed in Figure 4 should be replaced by Tyco
Electronics to ensure quality and reliability of the tool.
Order replacement parts through your Tyco Electronics
Representative, or call 1–800–526–5142, or refer to the
appropriate website:
Tools may also be returned for evaluation and repair. For
tool repair service, contact a Tyco Electronics
Representative at: 1–800–526–5136, or reference the
appropriate website above.
6. REVISION SUMMARY
RING, Retaining
DESCRIPTION
NOTE
220.22 [8.670]
S [e-mail]
S [e-mail]
S [e-mail]
S [e-mail]
S Updated document to corporate requirements
S Added NOTE to Figure 1
S Added new artwork and dimensions to Figure 4
The insulation crimper does not bottom on the
insulation anvil.
15.75 [.620]
QTY PER TOOL
4
27.43 [1.080]
408-8547
70.36
[2.770]
Rev
D
E