91504-1 Tyco Electronics, 91504-1 Datasheet - Page 4

• Manufacturer Part Number: 91504-1
• Description: TOOL CRIMP MATE-N-LOK 14-20AWG
• Manufacturer: Tyco Electronics
• Series: Certi-Crimp™ II, Commercial MATE-N-LOK®r
• Type: Crimpersr

Specifications of 91504-1

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Tools ,tyco Electronics / Amp: ROHS COMPLIANT
• Product: Crimping, Stripping & Cutting Tools & Drills
• Fits Cable/wire: 20-14 AWG
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 14-20 AWG
• For Use With: 170121-4 - CONN SOCKET M-N-L 14-20AWG TIN170121-1 - CONN SOCKET M-N-L 14-20AWG TINA25561 - CONN PIN 14-20AWG TIN CRIMPA25562 - CONN SOCKET 14-20AWG TIN CRIMPA25565 - CONN SOCKET 14-20AWG GOLD CRIMPA25568 - CONN PIN 16-18AWG TIN CRIMPA25570 - CONN SOCKET 16-18AWG TIN CRIMPA1435 - CONN SOCKET 14-20AWG GOLD CRIMPA1434 - CONN PIN 14-20AWG GOLD CRIMPA1421 - CONN SOCKET 14-20AWG TIN CRIMPA1420 - CONN PIN 14-20AWG TIN CRIMP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A9908

4.5. CERTI-CRIMP Ratchet Inspection
The CERTI–CRIMP ratchet feature on these hand tools
should be checked to ensure that the ratchet does not
release prematurely, allowing the crimping dies to open
before they have fully bottomed. Obtain a 0.025–mm
[.001–in.] shim that is suitable for checking the clearance
between the bottoming surfaces of the crimping dies.
Proceed as follows:
CERTI-CRIMP II Straight Action Hand Tools
50.04
[1.970]
4
of 4
1. Select the maximum size wire and strip it
according to dimensions listed in the drawing shipped
with the tool.
2. Select contact and crimp section corresponding to
the selected wire size (refer to the drawing shipped
with the tool).
3. Position the contact and wire in the crimping dies,
as described in the CRIMPING PROCEDURE
section.
4. Hold the wire in place and squeeze the handles
until the CERTI–CRIMP ratchet releases. Hold the
handles in this position, maintaining just enough
tension to keep the dies closed.
5. Check the clearance between the bottoming
surfaces of the wire crimper and the wire anvil. See
Figure 1. If the clearance is 0.025 mm [.001 in.] or
less (on at least two of the bottoming surfaces), the
ratchet is satisfactory. If clearance exceeds 0.025 mm
[.001 in.], the ratchet is out of adjustment and must be
repaired. See Section 5.
29.46 [1.160]
ITEM
1
19.81 [.780]
41.91 [1.650]
12.19 [.480]
76.71 [3.020]
PART NUMBER
21045-3
1
D
Closed to Last Ratchet Point Before Release
Tyco Electronics Corporation
REPLACEABLE PARTS
296.93 [11.690]
Figure 4
5. REPLACEMENT AND REPAIR
Replacement parts are listed in Figure 4. Parts other
than those listed in Figure 4 should be replaced by Tyco
Electronics to ensure quality and reliability of the tool.
Order replacement parts through your Tyco Electronics
Representative, or call 1–800–526–5142, or refer to the
appropriate website:
Tools may also be returned for evaluation and repair. For
tool repair service, contact a Tyco Electronics
Representative at: 1–800–526–5136, or reference the
appropriate website above.
6. REVISION SUMMARY
RING, Retaining
DESCRIPTION
NOTE
220.22 [8.670]
S [e-mail]
S [e-mail]
S [e-mail]
S [e-mail]
S Updated document to corporate requirements
S Added NOTE to Figure 1
S Added new artwork and dimensions to Figure 4
The insulation crimper does not bottom on the
insulation anvil.
15.75 [.620]
QTY PER TOOL
4
27.43 [1.080]
408-8547
70.36
[2.770]
Rev
D
E