45575-1 Tyco Electronics, 45575-1 Datasheet - Page 2
45575-1
Manufacturer Part Number
45575-1
Description
DAHT PG BUTT 14-16
Manufacturer
Tyco Electronics
Series
Certi-Crimp™ II, Plasti-Grip™r
Specifications of 45575-1
Tool Type
Hand Crimper
Features
Side Entry, Ratchet
For Use With/related Products
Splices, 14-22 AWG
For Use With
328427 - CONN BUTT SPLICE 14-16AWG NATRL8-34204-1 - SPLICE PG BUTT 16-148-55792-1 - SPLC,BUTT,PG 22-16COMM22-18MIL8-324138-1 - PG BUTT SPLC 22-16COMM22-18MIL2-35244-1 - CONN SPLICE BUTT 16-14AWG8-35244-1 - CONN SPLICE BUTT 16-14AWG STD8-34068-1 - CONN SPLICE BUTT 16-14AWG STD8-328427-1 - CONN SPLICE BUTT 16-14AWG STD8-55785-1 - CONN SPLICE BUTT 16-14AWG TIN55792-1 - CONN BUTT SPLICE 16-22AWG RED324138 - CONN SPLICE BUTT 22-16AWG TIN8-34243-1 - CONN SPLICE BUTT 22-16AWG REDA28185 - CONN SPLICE BUTT 14-16AWG BLUE8-34071-1 - CONN SPLICE BUTT 14-16 AWG P-G8-34070-1 - CONN SPLICE BUTT 16-22 AWG P-G8-34067-1 - CONN SPLICE BUTT 16-22 AWG P-GA27462 - CONN SPLICE BUTT 16-22 AWG P-GPA27542 - CONN SPLICE BUTT 14-16 AWG CLRA27465 - CONN SPLICE BUTT 14-16 AWG PL-GPA27463 - CONN SPLICE BUTT16-22 AWG PL-GPA27464 - CONN SPLICE BUTT 14-16 AWG .140A09034 - CONN SPLICE BUTT 14-16 AWG P-GPA09033 - CONN SPLICE BUTT 16-22 AWG .120A0998 - CONN SPLICE BUTT 14-16 AWG .170A0997 - CONN SPLICE BUTT 16-22 AWG .140
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
A27987
Rev H
Proceed as follows:
Insulation
Barrel
Range (AWG)
Typical PLASTI-GRIP
Butt Splice
1. Strip the wire using the appropriate strip
length dimensions provided in Figure 2. Do NOT
nick or cut the wire strands.
2. Open the crimping jaws by squeezing the tool
handles together until the ratchet releases.
3. Insert stripped wire into the splice wire barrel.
4. Locate the splice—with the wire inserted—
into the crimping jaws, as shown in Figure 3. The
end of the splice should rest against the locator.
NOTE
Wire Size
NOTE
22-16
16-14
i
i
6.35-7.14 [.250-.281]
Wire Strip Length
Similar splices with an insulation color other than
red or blue can be crimped with these tools;
however, wire size must be used, instead of the
tool-to-product color code, to establish
compatibility.
A complete list of butt splice part numbers cannot
be maintained on this document. For all part
numbers and their description, refer to your Tyco
Electronics representative.
8-328427-1
2-34071-2
8-34071-1
8-34071-4
8-34071-5
55792-1
55785-1
324138
328427
Splice
34203
34067
34070
34178
34243
34204
34068
34071
35244
Figure 2
Wire Barrel
Color Code
(Splice and
Tool)
Blue
Red
45575-1
45160
Tool
4. INSULATION CRIMP ADJUSTMENT
Each tool has three insulation crimp adjustment
positions to adjust the wire insulation grip: 1—Tight,
2—Medium, and 3—Loose. To obtain the desired
insulation grip, proceed as follows:
Crimping Butt Splice
5. Hold wire in place and squeeze tool handles
together until the CERTI--CRIMP ratchet
releases. Allow tool handles to open FULLY.
Remove the crimped splice from the tool.
6. To crimp other half of splice, position the
uncrimped wire barrel in the tool, and crimp as
described in Step 5.
7. Remove the crimped splice from the tool, and
inspect the crimp. Make sure the proper crimp
dot code is shown on the splice insulation for the
appropriate hand tool. Refer to Figure 4.
NOTE
End of Splice Resting
Against Locator
45575-1
45160
i
Tool
For detailed crimp inspection requirements, refer
to Application Specification 114--2161.
Crimp Dot Code
Locator
Color Code
Blue
Red
Figure 3
Figure 4
Crimp Dot Code
2 Dots
1 Dot
408-1502
2 of 6