91338-2 Tyco Electronics, 91338-2 Datasheet

no-image

91338-2

Manufacturer Part Number
91338-2
Description
TOOL HAND PRO CRIMPER 20-18AWG
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Datasheet
1.91338-2.pdf (6 pages)

Specifications of 91338-2

Tool Type
Fiber Optic, Hex or Round Crimp
Features
Side Entry
For Use With/related Products
Contacts, 18-20 AWG
Lead Free Status / RoHS Status
Not applicable / Not applicable
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
{ Supplied with die assembly. Also available separately.
} Contact the Tooling Assistance Center or Product Information (at the number listed below) for specific contact part numbers.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool Assembly
91338--1 consists of Die Assembly 91338--2 and
PRO--CRIMPER III Hand Crimping Tool Frame
354940--1. The die assembly consists of crimping
dies and a locator assembly.
Read these instructions thoroughly before crimping
any contacts.
Reason for revision will be listed in Section 11,
REVISION SUMMARY.
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool and
is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. A variety of tools is offered to satisfy your
performance requirements. For additional information, contact the Tooling
Assistance Center at 1- - 800- - 722- - 1111.
TE Die Assembly
NOTE
i
91338 2
91338--2
All dimensions on this document are in
millimeters [with inches in brackets]. Figures are
not drawn to scale.
Locator Assembly{
Die Assembly
58515 1
58515--1
Contact Support
Ratchet Adjustment
Wheel
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
Locator
Assembly
PRO- CRIMPER* III Hand Crimping
Tool Assembly 91338- 1
with Die Assembly 91338- 2
Moving Jaw
Product Family}
Contacts
0.64 mm
0.64 mm
Figure 1
2. DESCRIPTION
The tool features a tool frame with a stationary jaw
and handle, moving jaw, moving handle, and
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping chambers. See Figure 1.
The die assembly features a wire anvil, insulation
anvil, wire crimper, and insulation crimper.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame.
Attached to the outside of the frame is a locator
assembly, which contains a locator and contact
retainer. A nut is used on the upper die retaining
screw to hold the locator assembly in place.
(AWG)
Size
20
18
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Insulation Diameter
Stationary Jaw
1.85 [.073]
2.13 [.084]
(Max.)
Wire
PRO- - CRIMPER III
Hand Crimping Tool Frame
354940- - 1 (408- - 9930)
Back of Tool
(Wire Side)
Movable Handle
Pivot Pin
Instruction Sheet
408- - 8377
22 JUL 09 Rev A
Stationary Handle
Strip Length
3 81 [ 150]
3.81 [.150]
1 of 6
LOC B

91338-2 Summary of contents

Page 1

... Contact the Tooling Assistance Center or Product Information (at the number listed below) for specific contact part numbers. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 91338--1 consists of Die Assembly 91338--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly ...

Page 2

... Slide the anvils and crimpers out of the tool jaws. Tyco Electronics Corporation 408- 8377 Tool Frame Short Die Retaining ...

Page 3

... Butt the wire barrel against the locator. Back of Tool (Wire Side) Contact Mating End Wire Contact Support Locator in Contact Wire Stop Slot Figure 3 Tyco Electronics Corporation Tool Stationary Jaw Wire Strip Length Wire Inserted to Locator Wire Stop ...

Page 4

... Make a sample crimp and measure the crimp height. If the dimension is unacceptable, continue to adjust the ratchet, and again measure a sample crimp. Screwdriver Ratchet Adjustment Wheel Lockscrew (Typ) Crimp Height Dimension “A” 1.07 [.042] 1.19 [.047] Tyco Electronics Corporation 408- 8377 (Figure 5) Figure 5 Rev A ...

Page 5

... Rev A If the dies are damaged or worn excessively, they must be replaced. Order repair kit and replaceable parts through your Tyco Electronics representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 717--986--7605, or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS CORPORATION ...

Page 6

... Dies 91338- 2 May Also Be Used with the Following Tools. PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 SDE PEW- 12 Hand Tool 9- 1478240- 0 ...