47823 Tyco Electronics, 47823 Datasheet

DIE TERMINYL 69051 2AWG

47823

Manufacturer Part Number
47823
Description
DIE TERMINYL 69051 2AWG
Manufacturer
Tyco Electronics
Datasheet
1.47820.pdf (8 pages)

Specifications of 47823

Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimping Dies 47820 through 47823 are used with
Crimping Head 69051 or Hand Tool 59974–1.
Crimping Dies 47824, 47825, 47915, and 47918 are
used with Crimping Head 69066. The dies crimp
pre–insulated AMPOWER* terminals onto wire sizes
4 through 1/0 AWG, TERMINYL* terminals and
splices onto wire sizes 8 through 4/0 AWG,
TERMINYL splices with step–down adapters onto
wire sizes 16–14 through 1/0 AWG, and
PLASTI–GRIP* terminals and splices onto wire sizes
8 through 4/0 AWG. Refer to Figure 1 to ensure
compatibility of crimping die, head or tool, and wire
size.
For detailed information about the head or tool, refer
to the instructions packaged with the head or tool.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
Typical Crimping
Dies
E
i
Dimensions in this document are in millimeters
[with inches in brackets]. Figures and illustrations
are for reference only and are not drawn to scale.
Figure 1
Each crimping die consists of a stationary die (nest)
and a moving die (anvil). The stationary die features a
locator. Each die contains a color code dot that
matches the color code of the terminal and splice.
When mated, the dies form a crimping chamber.
1. Remove latch pin and open yoke on crimping
head. See Figure 2.
2. Loosen the setscrew in the yoke.
3. Insert the shank of the stationary die into the
yoke, and tighten the setscrew.
4. Extend the ram until the ram setscrew is visible.
5. Loosen the setscrew in the ram.
6. Insert the shank of the moving die into the ram,
and tighten the setscrew.
i
To avoid personal injury, ALWAYS release
hydraulic pressure to hose or control and
disconnect power unit from power supply before
installing or removing dies.
The stationary die has a large shank and the
moving die has a small shank, as shown in
Figure 2.
Figure 2

47823 Summary of contents

Page 1

... Typical Crimping Dies Figure 1 Crimping Dies 47820 through 47823 are used with Crimping Head 69051 or Hand Tool 59974–1. Crimping Dies 47824, 47825, 47915, and 47918 are used with Crimping Head 69066. The dies crimp pre–insulated AMPOWER* terminals onto wire sizes ...

Page 2

... Figure 3 Tyco Electronics Corporation Wire Stop Ç Ç Ç Ç É É É Ç Ç Ç Ç Window Indent 11.51-12.29 [.453-.484] 15.47-16.26 [.609-.640] 15.47-16.26 [.609-.640] 11.51-12.29 [.453-.484] 18 ...

Page 3

... For example, use Crimping Die 47820 (for wire size 8 AWG) to crimp both ends of the splice with step–down adapter for stepping down from wire size 8 to 16–14 AWG. Tyco Electronics Corporation 408-1729 Edge of Window Indent Resting Against ...

Page 4

... Blue 47822 47822 Yellow Yellow 47823 Red 1 47824 Blue Figure 6 3. Insert stripped wire into the wire barrel of the end of the splice to be crimped until the wire bottoms against the wire stop within the splice. Refer to Figure 3. 4. Remove crimping head latch pin, and open yoke ...

Page 5

Crimping Dies 47820 through 47825, 47915, and 47918 If butt splice sticks in die after crimping, apply a NOTE rocking action to the butt splice to remove it from i the die. Wipe light oil on dies to reduce sticking, ...

Page 6

... Suggested Plug Gage Design GO Diameter Die Closure Configuration 5.105-5.113 47820 [.2010-.2013] 6.020-6.027 47821 [.2370-.2373] 6.833-6.840 47822 [.2690-.2693] 8.103-8.110 47823 [.3190-.3193] 10.185-10.193 47824 [.4010-.4013] 11.354-11.361 47825 [.4470-.4473] 12.675-12.682 47915 [.4990-.4993] 14.249-14.257 47918 [.5610-.5613] ...

Page 7

... TYCO ELECTRONICS CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105–3608 NO-GO Dies may be returned for evaluation and repair. For Element die repair service, contact a Tyco Electronics Representative at 1–800–526–5136. 8. REVISION SUMMARY S Updated document to corporate requirements S New format Tyco Electronics Corporation ...

Page 8

... Plate, Flare 45992-7 45992-8 45992-9 Plate, Flare, Lower 45992-4 45992-5 45992-6 Plate, Flare, Upper 47947 Die, Moving 47946 Die, Stationary 313336-3 Locator 2-306105-5 Screw 21018-5 Nut 2-21000-2 Screw 313322-2 Plate, Flare 304385 Plate, Flare, Lower Figure 11 Tyco Electronics Corporation View Rev ...