58062-1 Tyco Electronics, 58062-1 Datasheet

HEAD ASSEMBLY TOOL FOR AMP MT CO

58062-1

Manufacturer Part Number
58062-1
Description
HEAD ASSEMBLY TOOL FOR AMP MT CO
Manufacturer
Tyco Electronics
Series
AMPMODU® MTr
Type
Terminating Head for AMPMODU MT Connectorsr
Datasheet
1.58062-1.pdf (5 pages)

Specifications of 58062-1

Connector Type
Receptacle
Crimp Handle
A2031-ND, 58075-1-ND, 58338-1-ND, 931800-1-ND
Crimp Or Cable Size
20-30 AWG
Crimp Application
Connectors
Product
Tool Component
For Use With
58075-1 - TOOL HANDLE PNEUMATIC W/O HEAD931800-1 - ELEC PWR UNIT W/O F/TRK OR HD58338-1 - PWR BENCH ASSEMBLY W/O HEADS104305-4 - CONN RCPT 8POS DL IDC .100 GOLD104305-2 - CONN RCPT 34POS DL IDC .100 GOLD104305-1 - CONN RCPT 10POS DL IDC .100 GOLD
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A2040
1. INTRODUCTION
Terminating Head 58062--1 is designed to terminate
unstripped discrete wire sizes 30 through 20 AWG
onto AMPMODU MT receptacle connectors having a
single row (reference part number 1--102747--7) or
double row (reference part number 102393--1)
of contacts with spacing on 2.54¢2.54 mm
[100¢100 in.] centerlines.
The head must be used with one of the following
power units (for operating procedure, refer to the
instructions packaged with the power unit).
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
2. DESCRIPTION
Features of the head and their function are as follows:
Wire inserter—forces the wire into the slotted beams
of the contact.
Note: Adapter for Single- - Row
Connectors Not Shown
E2010 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
Pistol Grip Manual Handle
Assembly 58074--1
Pistol Grip Pneumatic Handle
Assembly 58075--1
Pneumatic Power Bench
Assembly 58338--1
Electric Power Unit 931800--1
NOTE
i
Power Unit
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are
not drawn to scale.
Anti- - Backup Pawl
(Not Shown)
(Figure 1)
Feed Slide
(Not Shown)
Ramp
Instruction Sheet (408) or
Slot
Customer Manual (409)
Feed Channel
408--6790
408--6789
408--9393
409--5746
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
Channel
Terminating Head 58062- 1
For AMPMODU* Mass Termination (MT)
Receptacle Connectors
Figure 1
Wire guide—holds the connector properly in relation
to the wire.
Adjuster (inserter rod)—is a piston for, and regulates
the travel of, the wire inserter.
Feed slide—automatically advances the connector
after each termination.
Anti--backup pawl—prevents the connector from
moving out of position after it has been advanced by
the feed slide.
An adapter is included with the head that must be
used for terminating single--row connectors.
After the head is installed onto the power unit, it
serves as a guide and support for the connector
during termination. The arrow on the top of the head
indicates the direction that the connector will move in
the head. The wires are terminated onto the
connector using the insulation displacement
technique.
3. SETUP
Wire Guide
1. For single--row connectors, refer to Figures 1
and 2, and install the adapter onto the head as
follows:
2. Install the head onto the power unit according to
the instructions packaged with the power unit.
Make sure to observe any cautions and dangers.
a. Align the side of the adapter with the side of
the head so that the bottom starts at the slot
and the clip starts at the ramp.
b. Slide the adapter into the slot until the clip
drops into the channel.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Wire Inserter
Adjuster
(Inserter Rod)
Instruction Sheet
408- - 9085
04 FEB 10 Rev B
1 of 5
LOC B

58062-1 Summary of contents

Page 1

... Shown) Slot Note: Adapter for Single- - Row Connectors Not Shown 1. INTRODUCTION Terminating Head 58062--1 is designed to terminate unstripped discrete wire sizes 30 through 20 AWG onto AMPMODU MT receptacle connectors having a single row (reference part number 1--102747--7) or double row (reference part number 102393--1) of contacts with spacing on 2.54¢ ...

Page 2

... Paragraph B. NOTE i Tyco Electronics Corporation For application requirements for the connectors, refer to the appropriate application specification: 114- - 25019 for single- - row connectors and 114- - 25032 for double- - row connectors. ...

Page 3

... Too Much Force During Straight Before Termination Termination Figure 4 Wire Insertion Depth Adjustment Turn COUNTERCLOCKWISE To Increase Wire Insertion Depth Tyco Electronics Corporation Arms of Insulation Support Barrel Partially Closed Wire Was Not Fully Inserted Before Termination Turn CLOCKWISE To Decrease Wire Insertion Depth ...

Page 4

... A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by Tyco Electronics to ensure quality and reliability. Order replacement parts through your representative, or call 1--800--526--5142, or send a facsimile of your purchase order to ...

Page 5

... SCREW, Self--Tapping HOUSING, Insert PAWL SPRING, Compression INSERTER, Wire GUIDE, Wire SCREW, Machine, 4--40¢.750 in. L PIN, Slotted Spring ADJUSTER SPRING, Compression ROD, Inserter SLIDE, Feed ADAPTER, Single--Row Figure 6 Tyco Electronics Corporation 14 12 44.45 [1.75] QTY PER HEAD ...