1-46673-1 Tyco Electronics, 1-46673-1 Datasheet

no-image

1-46673-1

Manufacturer Part Number
1-46673-1
Description
TOOL HEAD CRIMP 22-16AWG STRATO
Manufacturer
Tyco Electronics
Series
Strato-Therm™r
Datasheet
1.1-46673-0.pdf (6 pages)

Specifications of 1-46673-1

Connector Type
Terminals and Splices
Crimp Handle
1213563-1, 1213804
Crimp Or Cable Size
16-22 AWG
Lead Free Status / RoHS Status
Not applicable / Not applicable
1. INTRODUCTION
Crimping Heads 1–46673–0, 1–46673–1, and
1–46988–0 are designed to crimp STRATO–THERM
Terminals and Splices onto wire size 26–14 AWG.
Refer to Figure 2. The crimping heads are used with
Double Action Battery Powered Hand Tool Kits
1213804–[ ].
This instruction sheet provides recommended
procedures for wire preparation, crimping head
installation, crimping, and maintenance and
E
NOTE
The crimping heads can also be used with the
626 Double Action Pneumatic Tool Adapter
1213563-1.
STRATO-THERM* Crimping Heads
Used with Double Action Battery
Powered Hand Tool Kits 1213804-[ ]
Figure 1
inspection. For information concerning tool setup and
operation, refer to Customer Manual 409–10056
packaged with the battery tool kit.
Reasons for reissue are provided in Section 8,
REVISION SUMMARY.
2. DESCRIPTION
The crimping head consists of integral jaws which
close in an arc–like motion. After an operator locates
the terminal or splice between the crimping jaws and
NOTE
Dimensions are in metric units with [inches in
brackets]. Figures and illustrations are for
reference only and are not drawn to scale.
www.tycoelectronics.com
408-10033
1

1-46673-1 Summary of contents

Page 1

... Reasons for reissue are provided in Section 8, REVISION SUMMARY. 2. DESCRIPTION The crimping head consists of integral jaws which close in an arc–like motion. After an operator locates the terminal or splice between the crimping jaws and 408-10033 1 www.tycoelectronics.com ...

Page 2

... WIRE TOOL TOOL SIZE (AWG) STRIP LENGTH 1-46673-0 22- 1-46673-1 [ 203- 234] [.203-.234] 1-46988-0 16-14 D For wires with thin-wall insulation. NOTE: Figure 2 3. HEAD INSTALLATION AND REMOVAL 3.1. Head Selection NOTE 3 ...

Page 3

... Refer to Section 5 and Figure 7 for crimp inspection. 4.2. Insulation Crimp Adjustment The insulation crimping section of the crimping head has three positions: 1—Tight; 2—Medium; and 3—Loose. 1. Insert insulation adjustment pins in Position 3. See Figure 6. A Rev STRATO-THERM Crimping Heads Splice Crimp (First Crimp) ...

Page 4

... Remove dust, moisture, and other contaminants with a clean, soft brush lint–free cloth. Do NOT use objects that could damage the head. 2. Make sure that all pins, rings, and other components are in place and secure. ...

Page 5

... GO Dim. GO W" Jaw Closure Configuration HAND HAND TOOL 1-46673-0 0.762-0.770 1-46673-1 [.0300-.0303] 1-46988-0 1.016-1.024 [.0400-.0403] Disconnect the battery and remove crimping DANGER head from tool before inspecting crimping chambers. 1. Remove oil and dirt from the jaw bottoming surfaces and plug gage element surfaces. ...

Page 6

... CUSTOMER SERVICE (38–35) TYCO ELECTRONICS CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105–3608 For further repair and replacement information, call the Tyco Electronics Tooling Assistance Center at the number at the bottom of page 1. 6 STRATO-THERM Crimping Heads REPLACEMENT PARTS ITEM PART NO. ...