69932 Tyco Electronics, 69932 Datasheet - Page 4

• Manufacturer Part Number: 69932
• Description: D W-DG 68075 69875 12-10AWG
• Manufacturer: Tyco Electronics

Specifications of 69932

• Lead Free Status / RoHS Status: Not applicable / Not applicable

{
but not under pressure.
4
68240-1
68241-1
68242-1
Die closure dimensions apply when wire barrel dies are bottomed
AMP-TAPEMATIC Crimping Dies
Configuration
69930
69931
69932
69954
69955
69956
Die Closure
of 6
SET
SET
DIE
Chipped
Edge
Suggested Plug Gage Design - Wire Barrel Crimp
A" Dim.
[.0460]
[.0540]
[.0760]
[.0590]
[.0750]
[.0910]
[.0510]
[.0590]
[.0830]
1.168
1.372
1.930
1.499
1.905
1.295
1.499
2.108
2.311
DIE CLOSURE
GO
DIM'S A"
NO-GO
[.0520]
[.0600]
[.0820]
[.0650]
[.0810]
[.0970]
[.0570]
[.0650]
[.0890]
1.321
1.524
2.083
1.651
2.057
2.464
1.448
1.651
2.261
B" Dim.
GO Dim.
{
}
Material – Tool Steel
Figure 3
Figure 4
[.0460-.0463]
[.0540-.0543]
[.0760-.0763]
[.0590-.0593]
[.0750-.0753]
[.0910-.0913]
[.0510-.0513]
[.0590-.0593]
[.0830-.0833]
1.168-1.176
1.372-1.379
1.930-1.938
1.499-1.506
1.905-1.913
2.311-2.319
1.295-1.303
1.499-1.506
2.108-2.116
GO
GAGE ELEMENT
25.4 [1.000]
Min. Typ.
DIM'S B"
6.35 [.250]
Min. Typ.
[.0519-.0520]
[.0599-.0600]
[.0819-.0820]
[.0649-.0650]
[.0809-.0810]
[.0969-.0970]
[.0569-.0570]
[.0649-.0650]
[.0889-.0890]
1.318-1.321
1.521-1.524
2.080-2.083
1.648-1.651
2.055-2.057
2.461-2.464
1.445-1.448
1.648-1.651
2.258-2.261
NO-GO
}
NO-GO Dim.
R" Radius
Pitted
Tyco Electronics Corporation
RADIUS
[.0620]
[.0780]
[.1090]
[.0740]
[.0860]
[.0620]
[.0780]
[.1090]
(MAX)
[.1180]
1.575
1.981
2.769
1.880
2.184
2.997
1.575
1.981
2.769
R"
B"
}
A. Wire Barrel Crimp Die Closure
B. Insulation Crimp Die Closure
69930
69931
69932
Material – Tool Steel
Configuration
SET
DIE
Die Closure
1. Clean oil or dirt from the die closure surfaces,
bottoming surfaces, and plug gage elements.
2. Assemble dies so that wire barrel dies are
bottomed but not under pressure.
3. With wire barrel dies bottomed, inspect the wire
barrel crimp die closure using the proper plug
gage. Hold gage in straight alignment with the die
closure and carefully insert, without forcing, the
GO element. See Figure 6A. The GO element
must pass completely through the wire barrel crimp
die closure.
4. Try to insert the NO–GO element. The NO–GO
element may enter partially, but must not pass
completely through the wire barrel crimp die
closure. See Figure 6A.
1. With wire barrel dies bottomed and not under
pressure, set insulation crimp dies at “gage”
dimension shown in Figure 6B.
2. Inspect the insulation crimp die closure using
the proper plug gage in the same manner as steps
(c) and (d) in paragraph 4.3.A. See Figure 6B
If both the wire barrel and insulation crimp die
closures meet the GO NO–GO gage conditions,
the dies may be considered dimensionally correct.
Suggested Plug Gage Design - Insulation Crimp
C" Dim.
[.0300]
[.0300]
[.0520]
See Figure 6B.)
0.762
0.762
1.321
DIE CLOSURE
GO
gage" dim.
(Dies set at
DIM'S C"
GO Dim.
NO-GO
[.0500]
[.0500]
[.0720]
1.829
1.27
1.27
D"
[.0300-.0303]
[.0300-.0303]
[.0520-.0523]
Figure 5
0.762-0.770
0.762-.0770
1.321-1.328
GO
6.35 [.250] Typ.
DIMENSION D"
ELEMENT
GAGE
[.0499-.0500]
[.0499-.0500]
[.0719-.0720]
1.826-1.829
1.267-1.27
1.267-1.27
NO-GO
}
NO-GO Dim.
D"
408-2648
E"
[.160]
[.190]
[.310]
Rev
4.06
4.83
7.87
DIM
E"
B