10962-2000 3M, 10962-2000 Datasheet

no-image

10962-2000

Manufacturer Part Number
10962-2000
Description
LACING FIXTURE UNIT MDR
Manufacturer
3M
Series
MDRr
Datasheet
1.10960-2000.pdf (6 pages)

Specifications of 10962-2000

Tool Type
Lacing Fixture Hand Press
Rohs Compliant
YES
For Use With/related Products
MDR Wiremount Plug
Lead Free Status / RoHS Status
Lead free / Vendor undefined
Other names
05113832693
80610714653
3
Instructions
For the Assembly of the MDR 101XX-6000
Wiremount Plug using the 10960-2000 MDR
Assembly Press and Related Accessories
The assembly of the MDR plug
requires the following tooling which
must be ordered individually prior to
any tooling set-up:
Figure 1. 10960-2000 Hand Press
• 10960-2000 .........Hand Press (Fig. 1)
• 10961 ..................Cutting Unit (Fig. 5); includes
• 10962-2000 .........Fixture Unit (Fig. 14); includes
• 10964-1 ...............Cable Clamp (Fig. 13); Black,
• 10964-2 ...............Cable Clamp (Fig. 13); Silver,
Optional:
• 10963-2000 .........Fixture Block (Fig. 12); Not required
2 spare blades (10970-9)
14, 20, 26, 36, 40, 50, 68, 80, and
100 position connector stops
14-50 position
68-100 position
for initial unit; only needs to be ordered
when additional stations are set-up.
Must also order another 10962-2000.
1
Initial Tooling Set Up
1.
2.
3.
4.
5.
Figure 2. Back of press
Unpack the items listed above and set them on a
clean work bench.
Select the 10960-2000 Hand Press and place it in front of
the operator so the handle is toward the operator. It is
recommended for assembling connectors that the press be
positioned in a manner so cable may hang freely below
the press when moving the shuttle block (C of Fig. 4).
Locate the thumbscrew (C of Fig. 2) at the back of the
press. Loosen the thumbscrew and gently lower the
armature of the press away from the operator (Fig. 3).
This allows easy access to the back of the press
to install the cutting unit.
Slide the platen assembly forward using the side bar
which has a round black knob (B of Fig. 4) on the
operator’s left side.
Select the 10961 cutting unit (Fig. 5). Install cutting unit
from the rear of the press. The “A” portion of the cutting
unit faces the front of the press with the “B” portion
going toward the back. Slide cutting unit forward
in the two grooves provided.
A.
Stop bracket
B.
Stop bracket
thumbscrew
C.
Thumbscrew
for press
D.
Shuttle
stop
2

10962-2000 Summary of contents

Page 1

... Press (Fig. 1) • 10961 ..................Cutting Unit (Fig. 5); includes 2 spare blades (10970-9) • 10962-2000 .........Fixture Unit (Fig. 14); includes 14, 20, 26, 36, 40, 50, 68, 80, and 100 position connector stops • 10964-1 ...............Cable Clamp (Fig. 13); Black, 14-50 position • ...

Page 2

... Height adjustment should be checked periodically. Fixture Unit Adjustment C. Once the size of the connector to be assembled has been Shuttle determined the 10962 Fixture Unit requires some adjustments. block 1. Select the correct connector stop (14, 20, 26, 36, 40, 50, 68 100 position Fig. 14) for your application. ...

Page 3

... Return fixture unit to shuttle block. Figure 6. Back side of 10962-2000 7. Fixture unit is now Fixture Unit ready for use. Cable Preparation Before assembly of the MDR 101XX-6000 Wiremount Plug can take place, the cable must be prepared ...

Page 4

Figure 8. Wires in “U” slot cover Figure 10. Cut wires E. Repeat for the next conductor, except position it to the rear and right. Place the next wire in the left slot (adjacent to the first one), followed by ...

Page 5

... Increased through-put and greater press utilization can be achieved by setting up additional wiring stations. When required, order one each of the 10963-2000 fixture block and one each of the 10962-2000 fixture unit. After the wires are properly positioned in the fixture unit, move the unit to the press for final termination of connector. ...

Page 6

... UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER’S PRODUCTS THAT WERE DEFECTIVE. Printed on recycled paper Litho in the USA © 3M 1994 34-7035-7169-4 (XXXX.X) ...