B43504A5337M EPCOS Inc, B43504A5337M Datasheet - Page 16

CAP 330UF 450V ELEC SNAP IN

B43504A5337M

Manufacturer Part Number
B43504A5337M
Description
CAP 330UF 450V ELEC SNAP IN
Manufacturer
EPCOS Inc
Series
B43504r
Datasheet

Specifications of B43504A5337M

Capacitance
330µF
Tolerance
±20%
Voltage Rating
450V
Lifetime @ Temp.
3000 Hrs @ 105°C
Operating Temperature
-25°C ~ 105°C
Features
General Purpose
Ripple Current
4.8A
Esr (equivalent Series Resistance)
410.0 mOhm
Impedance
490 mOhm
Mounting Type
Through Hole
Package / Case
Radial, Can - Snap-In
Size / Dimension
1.181" Dia (30.00mm)
Height
1.969" (50.00mm)
Lead Spacing
0.394" (10.00mm)
Operating Temperature Range
- 25 C to + 105 C
Diameter
30 mm (1.18 in)
Length
50 mm
Product
Aluminum Electrolytic Capacitors
Termination Style
Snap In
Esr
410 mOhms
Load Life
3000 hrs
Number Of Pins
2, 3
Test Frequency
100 Hz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Surface Mount Land Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
495-4252

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
B43504A5337M000
Manufacturer:
EPCOS
Quantity:
30 000
Part Number:
B43504A5337M007
Manufacturer:
EPCOS
Quantity:
30 000
Part Number:
B43504A5337M060
Manufacturer:
EPCOS
Quantity:
30 000
Part Number:
B43504A5337M067
Manufacturer:
EPCOS
Quantity:
30 000
Part Number:
B43504A5337M080
Manufacturer:
EPCOS
Quantity:
30 000
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Polarity
Reverse voltage
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Please read Cautions and warnings and
Important notes at the end of this document.
B43504
Compact
Safety information
Make sure that polar capacitors are connected
with the right polarity.
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature
limits during soldering.
105 C
Page 16 of 20
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1
"Mounting positions of
capacitors with screw
terminals"
11.4
"Mounting
considerations for
single-ended capacitors"
11.3
"Mounting torques"
11.5
"Soldering"

Related parts for B43504A5337M