CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CG
Series
Capacitance
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan )
ESR (
Leakage Current (
Temperature Characteristics
(Max.Impedance Ratio)
Endurance
Damp Heat
(Steady State)
Resistance to
Soldering Heat
Marking
Size
Item
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
3 Initial value : The value before test of examination of resistance to soldering.
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
Specifications
Dimensions
L
A
B
C
E
H
D
Dimension table in next page.
0.5 to 0.8
1)
5
5.0
5.9
6.0
5.3
5.3
1.6
6L
Voltage ( j:6.3v)
Lot No.
0.5 to 0.8
Chip Type, Higher Capacitance
series
6.3
minutes at 105°C.
6.3
5.9
7.3
6.6
6.6
2.1
2)
6L
– 55 to +105°C
2.5 to 16V
47 to 3300µF
± 20% at 120Hz, 20°C
Less than or equal to the specified value at 120Hz, 20°C
Less than or equal to the specified value at 100kHz, 20°C
Less than or equal to the specified value.
Z+105°C / Z+20°C
Z – 55°C / Z+20°C
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
0.8 to 1.1
8
8.0
6.9
9.0
8.3
8.3
3.2
7L
Plastic platform
L
+0.1
- 0.4
0.8 to 1.1
10
0.3 MAX.
10.0
11.0
10.3
10.3
7.9
4.6
8L
0.8 to 1.1
10
10.0
11.0
10.3
10.3
1.25
1.25
9.9
4.6
10L
C 0.2
0.8 to 1.1
H
10 12.7L
(100kHz)
10.0
12.6
11.0
10.3
10.3
4.6
(mm)
After 2 minutes' application of rated voltage at 20°C
Positive
Negative
Performance Characteristics
CG
Capacitance
CF
Higher
Type numbering system (Example : 6.3V 470µF)
P
1
Voltage
Capacitance change
tan
ESR
Leakage current (
Capacitance change
tan
ESR
Leakage current (
Capacitance change
tan
ESR
Leakage current (
C
Code
2
V
G
3
(
(
(
0
4
1)
1)
1)
J
5
2.5
e
4
6
7
2)
2)
2)
7
4
g
1
8
Within ± 20% of the initial capacitance value (
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Within ± 20% of the initial capacitance value (
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Within ± 10% of the initial capacitance value (
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
M
9
6.3
j
C
10
L
11
10
A
12
1
G
13
16
C
14
S
Capacitance toleranc ( 20%)
Rated capacitance (470 F)
CAT.8100Z
Rated voltage (6.3V)
Configuration
Series name
Taping code
3)
3)
3)
Type