C1206C561K5GACTU Kemet, C1206C561K5GACTU Datasheet - Page 6
![CAP CERAMIC 560PF 50V NP0 1206](/photos/10/53/105350/1206_kemet_mlcc_caps_sml.jpg)
C1206C561K5GACTU
Manufacturer Part Number
C1206C561K5GACTU
Description
CAP CERAMIC 560PF 50V NP0 1206
Manufacturer
Kemet
Series
C1206r
Specifications of C1206C561K5GACTU
Capacitance
560pF
Voltage - Rated
50V
Tolerance
±10%
Temperature Coefficient
C0G, NP0
Mounting Type
Surface Mount, MLCC
Operating Temperature
-55°C ~ 125°C
Applications
General Purpose
Package / Case
1206 (3216 Metric)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Thickness
0.78mm
Voltage Rating
50 Volts
Operating Temperature Range
- 55 C to + 125 C
Temperature Coefficient / Code
C0G (NP0)
Product
General Type MLCCs
Dimensions
1.6 mm W x 3.2 mm L x 1.5 mm H
Dissipation Factor Df
0.1
Termination Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Ratings
-
Lead Spacing
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
399-1215-2
C1206C561K5GAC
C1206C561K5GAC7800
C1206C561K5GAC
C1206C561K5GAC7800
94
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
3. Tape with components shall pass around radius “R” without damage (see sketch A). The minimum trailer length (Fig. 2) may require
4. The cavity defined by A
embossment location and hole location shall be applied independent of each other.
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
reels (with C-7280). Note that 13” reels are preferred.
Refer to EIA-556.
12 mm
12 mm
8 mm
8 mm
and
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Double
+0.004, -0.0)
(4 mm)
(8 mm)
Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
Single
+0.10 -0.0
12 mm
(0.059
8 mm
1.5
0
, B
0
, and K
(0.173)
(0.323)
ALUMINUM CHIP CAPACITORS
4.4
8.2
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
1.0 Kg Minimum.
TANTALUM, CERAMIC AND
1.75 ±0.10
0
The total peel strength of the cover tape from the carrier tape shall be:
shall be configured to surround the part with sufficient clearance such that the chip does not pro-
0.1 Newton to 1.0 Newton (10g to 100g)
0.1 Newton to 1.3 Newton (10g to 130g)
(0.039) (0.138 ±0.002)
(0.059) (0.217 ±0.002)
1.0
1.5
Packaging Information
4.0 ±0.10
3.5 ±0.05
5.5 ±0.05
Figure 1
(0.157 ±0.004) (0.984)
(0.315 ±0.004) (1.181)
2.0 ±0.05
4.0 ±0.10
8.0 ±0.10
(Metric will govern)
(0.024)
0.600
25.0
30.0
(0.098)
(0.181) (0.472 ±0.012)
(0.004)
0.100
2.5
4.6
(.315 ±0.012)
12.0 ±0.30
8.0 ±0.30