C1812X224K2RACTU Kemet, C1812X224K2RACTU Datasheet - Page 11
![CAP CER .22UF 200V X7R 1812 FT](/photos/0/97/9734/399-1812_sml.jpg)
C1812X224K2RACTU
Manufacturer Part Number
C1812X224K2RACTU
Description
CAP CER .22UF 200V X7R 1812 FT
Manufacturer
Kemet
Series
FT-CAPr
Datasheet
1.C1812X224K2RACTU.pdf
(18 pages)
Specifications of C1812X224K2RACTU
Capacitance
0.22µF
Voltage - Rated
200V
Tolerance
±10%
Temperature Coefficient
X7R
Mounting Type
Surface Mount, MLCC
Operating Temperature
-55°C ~ 125°C
Features
Soft Termination
Applications
Boardflex Sensitive
Package / Case
1812 (4532 Metric)
Size / Dimension
0.177" L x 0.126" W (4.50mm x 3.20mm)
Thickness
1.55mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Ratings
-
Lead Spacing
-
Other names
399-5523-2
C1812X224K2RAC
C1812X224K2RAC7800
C1812X224K2RAC
C1812X224K2RAC7800
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C1812X224K2RACTU
Manufacturer:
KEMET
Quantity:
600 000
SMD MLCCs – Flexible Termination System (FT-CAP), X7R Dielectric, 6.3VDC-250VDC (Commercial Grade & Automotive Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
2. The tape with or without components shall pass around R without damage (see Figure 5).
3. If S
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Tape Size
Tape Size
B
hole location shall be applied independent of each other.
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4).
(e) for KPS Series product A
(f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
12mm
16mm
12mm
16mm
1
8mm
8mm
S
1
<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)).
1
B
including draft concentric about B
1
is for tape feeder reference only,
T
T
Ko
T
(0.059 +0.004/-0.0)
Cover Tape
2
1
Single (4mm) &
Double (8mm)
1.5 +0.10/-0.0
Triple (12mm)
Single (4mm)
Pitch
D
0
0
, B
Center Lines of Cavity
0
and K
0
and B
o
.
0
shall surround the component with sufficient clearance that:
0
are measured on a plane 0.3mm above the bottom of the pocket.
B
D
(0.039)
(0.059)
(0.323)
(0.476)
Note 1
Note 4
(0.171)
ØDo
1
4.35
1
12.1
8.2
1.0
1.5
User Direction of Unreeling
Max.
Min.
P
Constant Dimensions — Millimeters (Inches)
Variable Dimensions — Millimeters (Inches)
2
(0.069 ± 0.004)
1.75 ± 0.10
Po
P
1
E
(0.246)
(0.404)
(0.561)
10.25
14.25
6.25
2
E
Min.
1
tolerance on tape ±0.2 mm]
[10 pitches cumulative
Ao
ØD
1
(0.157 ± 0.004)
(0.138 ± 0.002)
(0.217 ± 0.002)
(0.217 ± 0.002)
Bo
3.5 ± 0.05
5.5 ± 0.05
5.5 ± 0.05
4.0 ± 0.10
see Note 1 Table 6
Embossment
For cavity size,
P
F
0
F
E
2
E
1
W
(0.079 ± 0.002)
(0.157 ± 0.004)
(0.315 ± 0.004)
(0.315 ± 0.004)
2.0 ± 0.05
4.0 ± 0.10
8.0 ± 0.10
8.0 ± 0.10
P
P
2
1
(0.984)
T
(0.098)
Note 2
(1.181)
(0.181)
(0.181)
R Ref.
25.0
2
2.5
4.6
4.6
30
Max
S
W Max
(0.327)
(0.484)
(0.642)
(0.024)
Note 3
0.600
12.3
16.3
1
8.3
C1013-1 • 9/14/2010
Min.
T Max.
(0.024)
0.600
A
0
Note 5
,B
0
& K
T
(0.004)
0.100
1
Max.
0
11