ISL84781 Intersil Corporation, ISL84781 Datasheet
ISL84781
Related parts for ISL84781
ISL84781 Summary of contents
Page 1
... All digital inputs are 1.8V logic-compatible when using a single +3V supply. The ISL84781 multiplexer device that is offered TSSOP package, and thin QFN package. Table 1 summarizes the performance of this family. TABLE 1. FEATURES AT A GLANCE ...
Page 2
... RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD- 020C. ISL84781IR (3x3 THIN QFN) TOP VIEW ...
Page 3
... C = 1.0nF Input OFF Capacitance 1MHz, V OFF 3 ISL84781 Thermal Information Thermal Resistance (Typical, Note TSSOP Package . . . . . . . . . . . . . . . . . . . . . . 16 Ld 3x3 Thin QFN Package . . . . . . . . . . . . . . . . . Maximum Junction Temperature (Plastic Package 150°C Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s 300°C ...
Page 4
... Address Transition Time 1.8V, V TRANS (See Figure 1, Note 9) Break-Before-Make Time 1.8V, V BBM (See Figure 3, Note 9) Charge Injection 1.0nF ISL84781 Test Conditions +2.7V to +3.3V, GND = 0V, V SUPPLY Unless Otherwise Specified (Continued) TEST CONDITIONS = V = 0V, (See Figure 6) NO COM = V = 0V, (See Figure 6) NO ...
Page 5
... Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1C. ADDRESS t MEASUREMENT POINTS TRANS OFF LOGIC ON INPUT SWITCH OUTPUT V OUT Q = Δ OUT L FIGURE 2A. Q MEASUREMENT POINTS 5 ISL84781 t < 5ns r t < 5ns f VNO0 OUT LOGIC 90% INPUT Repeat test for other switches. C capacitance. t < 5ns r t < 5ns ...
Page 6
... NOx ANALYZER COM GND R L Off-Isolation is measured between COM and “Off” NO terminal on each switch. Signal direction through switch is reversed and worst case values are recorded. FIGURE 4. OFF ISOLATION TEST CIRCUIT 6 ISL84781 (Continued) t < 5ns r t < 5ns f VNOx LOGIC 90% INPUT Repeat test for other switches. C capacitance ...
Page 7
... DIODE FIGURE 7. OVERVOLTAGE PROTECTION 7 ISL84781 Power-Supply Considerations The ISL84781 construction is typical of most single supply CMOS analog multiplexers, in that it has two supply pins: V+ and GND. V+ and GND drive the internal CMOS switches = 16ns, ON and set its analog voltage limits. Unlike switches with a 4V maximum supply voltage, the ISL84781 4 ...
Page 8
... COM FIGURE 10. ON RESISTANCE vs SWITCH VOLTAGE 8 ISL84781 signal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal. This is why both sides of a given switch can show leakage currents of the same or opposite polarity ...
Page 9
... V+ (V) FIGURE 14. INHIBIT TURN-ON TIME vs SUPPLY VOLTAGE GAIN -10 PHASE R = 50Ω 0. P-P P-P 0 FREQUENCY (MHz) FIGURE 16. FREQUENCY RESPONSE 9 ISL84781 T = 25°C, Unless Otherwise Specified (Continued 3.5 4 4.5 1 FIGURE 13. ADDRESS TRANS TIME vs SUPPLY VOLTAGE 3.5 4 4.5 FIGURE 15. INHIBIT TURN-OFF TIME vs SUPPLY VOLTAGE ...
Page 10
... Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND (QFN Paddle Connection: To Ground or Float) TRANSISTOR COUNT: 228 PROCESS: Submicron CMOS 10 ISL84781 FN6095.3 July 31, 2006 ...
Page 11
... Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimen- sions are not necessarily exact. (Angles in degrees) 11 ISL84781 M16.173 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE ...
Page 12
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 ISL84781 L16.3x3A C A ...