EN3P3MX Switchcraft Inc., EN3P3MX Datasheet - Page 4

• Manufacturer Part Number: EN3P3MX
• Description: CONN RCPT 3POS MALE PANEL #20
• Manufacturer: Switchcraft Inc.
• Series: EN3™r
• Type: Panel Plugr

Specifications of EN3P3MX

• Rohs Information: Switchcraft RoHS Info.
• Connector Type: Receptacle, Male Pins
• Number Of Positions: 3
• Mounting Type: Panel Mount, Bulkhead - Front Side Nut
• Termination: Solder Cup
• Fastening Type: Threaded
• Orientation: Keyed
• Ingress Protection: IP67/68 - Dust Tight, Waterproof
• Shell Material, Finish: Thermoplastic Polymer, Glass Fiber
• Product Type: Connectors
• Contact Style: Pin (Male)
• Shell Style: Receptacle
• Number Of Positions / Contacts: 3
• Mounting Style: Flange
• Termination Style: Solder Cup
• Contact Plating: Gold
• Current Rating: 3 A
• Voltage Rating: 600 V
• Angle: Straight
• Application: Commercial
• Brand/series: EN3 Series
• Current, Rating: 7.5 A
• Flammability Rating: UL94-V0
• Housing Type: Plastic
• Ip Rating: IP 66/68
• Material, Housing: Thermoplastic Rubber
• Number Of Contacts: 3
• Primary Type: Sealed
• Voltage, Rating: 600 V
• Wire, Awg: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Shell Size - Insert: -
• Shell Size, Military: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SC261

STEP 1:
PRESS THE TWO WINGS OF CABLE CLAMP INWARD, THEN THREAD NUT CLOCKWISE ONTO CABLE CLAMP
TO THE POSITION SHOWN.
EN3™ SERIES FIELD ASSEMBLY INSTRUCTIONS FOR CRIMP CONTACTS:
CORD CONNECTOR
STEP 2:
FEED THE FREE END OF CABLE THROUGH BOOT, CABLE CLAMP,
AND COUPLING RING IN THE ORDER SHOWN.
NOTE: CUT-OFF END OF BOOT FOR LARGER THAN 0.280"
STRIP CABLE END AND CONDUCTORS AS SHOWN.
CRIMP CONDUCTORS TO CONTACTS.
USE CRIMP HAND TOOL EN3CR OR PNEUMATIC CRIMP TOOL
EN3CRAUTO WITH #26 POSITIONER EN3POS26.
INSERT CONTACTS TO CONNECTOR HOUSING PER CONTACT
ARRANGEMENTS AND INSERTION INSTRUCTIONS.
STEP 3:
ALIGN TABS OF COUPLING RING WITH NOTCHES OF
CORD HOUSING AND PUSH COUPLING RING ONTO
CORD HOUSING.
STEP 4:
ALIGN CABLE CLAMP AND PUSH FORWARD UNTIL IT
SNAP-LOCKS ONTO THE REAR OF CONNECTOR HOUSING.
TURN NUT OF CABLE CLAMP COUNTERCLOCKWISE
UNTIL CABLE CLAMP TIGHTENS AGAINST CABLE.
STEP 5:
PUSH BOOT ALL THE WAY FORWARD, OVER
CABLE CLAMP, UNTIL FRONT END OF BOOT
SEALS TIGHTLY ONTO CONNECTOR HOUSING.
CABLE CLAMP
TYPICAL CONTACT INSERTION INSTRUCTIONS:
PLACE CONTACT IN GROOVE OF INSERTION HAND TOOL
EN3INS26. NOTE: TIP OF TOOL SHOULD BE UP AGAINST
THE SHOULDER OF CONTACT.
INSERT CONTACT INTO CORRECT CAVITY OF CONNECTOR
BODY BY APPLYING CONSTANT PRESSURE UNTIL
CONTACT BOTTOMS UP AGAINST LOCKING DISC.
NOTE: DO NOT TILT TOOL DURING THE INSERTION.
REPEAT ABOVE PROCEDURE TO INSERT ALL CONTACTS
PER CONTACT ARRANGEMENTS.
DIAMETER CABLES.
CONTACTS
CRIMP
NUT
COUPLING RING
CABLE CLAMP
CORD WIRING SIDE VIEW
CORD HOUSING
CONTACT
LOCKING DISC
BOOT
CABLE CLAMP WITH NUT
IN POSITION
NOTCH,
PIN #1 INDICATOR
CUT-OFF END OF BOOT HERE FOR
LARGER THAN 0.280" DIA. CABLES
CABLE
.75 19.1
.156 4.0
CONDUCTOR
INSERTION
HAND TOOL
CABLE