MGDQ5-00019 Tyco Electronics, MGDQ5-00019 Datasheet - Page 3

• Manufacturer Part Number: MGDQ5-00019
• Description: INDUCTOR 150UH 1A 20% SMD 1260
• Manufacturer: Tyco Electronics
• Series: MGDQ5r
• Type: Drum Corer

Specifications of MGDQ5-00019

• Inductance: 150µH
• Current: 1A
• Current - Saturation: 1A
• Tolerance: ±20%
• Dc Resistance (dcr): 230 mOhm Max
• Package / Case: 0.504" L x 0.504" W x 0.236" H (12.80mm x 12.80mm x 6.00mm)
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Frequency - Test: 100kHz
• Applications: EMI Filter
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Shielding: -
• Q @ Freq: -
• Self Resonant Freq: -
• Current - Temperature Rise: -

Environmental
General
Other
Chemical
Static Humidity
Storage Life
Temperature Cycle
Temperature Shock
IR Reflow
Storage Temperature
Range
Operating
Temperature Range
Flammability
Vibration
Mechanical Shock
Solderability
Component Adhesion
(Push Test)
Resistance to Solvent
Ionic Contamination
Item
For Print Distribution to Customers
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
10 seconds at 260°C max.
-40°C to +85°C
-40°C to +85°C
IEC 695-2-2
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
Wetting shall cover 90% minimum of
each termination
Component shall withstand 6 lb. push
force minimum without delaminating
from mounting surface.
Conductivity:
pH:
Chlorides:
Sodium:
Potassium:
Specification
Precondition at 25°C for 60 minutes. Expose parts to an
environment of +40°C with 90 to 95% R.H. for 240 hours.
Subject parts to an environment of 85°C 85% R.H. for 168
hours. After exposure allow parts to dry for 4 hours before
measurements are taken.
10 cycles (Air to Air) 1 cycle shall consist of:
30 minutes exposure to +85°C
30 minutes exposure to -40°C
Allow 20 minutes transition between extremes.
10 cycles (Air to Air) 1 cycle shall consist of:
30 minutes exposure to -55°C
30 minutes exposure to +125°C
15 seconds maximum transition between temperatures
Post test parts shall pass all electrical specifications after reflow.
There shall be no visible signs of solder flow or leakage
from the part.
Withstands needle-flame test
1 cycle of 30 minutes of the following:
5 - 7 Hz constant displacement of 0.75 inches, 5 minutes
7 - 30 Hz constant acceleration of 1.5 Gs, 10 minutes
31 - 50 Hz constant displacement of 0.33 inches, 5 minutes
50 - 500 Hz constant acceleration of 1.2 Gs, 10 minutes
MGDQ1 Series - 500 Gs per axis, 2 directions
MGDQ2 Series - 500 Gs per axis, 2 directions
MGDQ3 Series - 500 Gs per axis, 2 directions
MGDQ4 Series - 500 Gs per axis, 2 directions
MGDQ5 Series - 500 Gs per axis, 2 directions
MGDQ6 Series - 500 Gs per axis, 2 directions
Dip pads in RMA
flux, 63/37 solder
(Sn/Pb) at 232°C for
5 seconds ±2
seconds.
Apply and measure force with a digital force gauge set.
Withstands 6 minutes of alcohol.
Withstands 3 minutes forced spray Freon TMS
11 µOhms/cm maximum
5.5 to 9
65 ppm maximum
20 ppm maximum
10 ppm maximum
Test Method/Condition
MGDQ5
Series
Sheet 3 of 3
Revision
A0