PIC12C672-04/P Microchip Technology, PIC12C672-04/P Datasheet - Page 224

• Manufacturer Part Number: PIC12C672-04/P
• Description: IC MCU OTP 2KX14 A/D 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Cr

Specifications of PIC12C672-04/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Ram Memory Size: 128Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Digital Ic Case Style: DIP
• Processor Series: PIC12C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 8
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMINGAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
Register 15-2:
DS31015A-page 15-4
bit 7
bit 6
bit 5
bit 4
SSPCON: Synchronous Serial Port Control Register
bit 7
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word
0 = No collision
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
0 = No overflow
In I
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In both modes, when enabled, these pins must be properly configured as input or output.
In SPI mode:
1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the
0 = Disables serial port and configures these pins as I/O port pins
In I
1 = Enables the serial port and configures the SDA and SCL pins as the source of the
0 = Disables serial port and configures these pins as I/O port pins
CKP: Clock Polarity Select bit
In SPI mode:
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
In I
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch) (Used to ensure data setup time)
WCOL
R/W-0
2
2
2
serial port pins
(must be cleared in software)
of overflow, the data in SSPSR is lost and the SSPBUF is no longer updated. Overflow can
only occur in slave mode. The user must read the SSPBUF, even if only transmitting data,
to avoid setting overflow. In master mode the overflow bit is not set since each new recep-
tion (and transmission) is initiated by writing to the SSPBUF register.
“don‘t care” in transmit mode. SSPOV must be cleared in software in either mode.
C mode:
C mode:
C mode:
serial port pins
SSPOV
R/W-0
SSPEN
R/W-0
R/W-0
CKP
SSPM3
R/W-0
SSPM2
R/W-0
1997 Microchip Technology Inc.
SSPM1
R/W-0
bit 0
SSPM0
R/W-0