PIC18F13K50-I/P Microchip Technology, PIC18F13K50-I/P Datasheet - Page 169

• Manufacturer Part Number: PIC18F13K50-I/P
• Description: IC PIC MCU FLASH 4KX16 20-PDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F13K50-I/P

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 20-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 14
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: EUSART/I2C/MSSP/SPI/USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM164127, DV164126
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 20PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164126 - KIT DEVELOPMENT USB W/PICKIT 2DM164127 - KIT DEVELOPMENT USB 18F14/13K50AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15.3.8
To initiate a Start condition, the user sets the Start
Enable bit, SEN bit of the SSPCON2 register. If the
SDA and SCL pins are sampled high, the Baud Rate
Generator
SSPADD<6:0> and starts its count. If SCL and SDA are
both sampled high when the Baud Rate Generator
times out (T
of the SDA being driven low while SCL is high is the
Start condition and causes the S bit of the SSPSTAT1
register to be set. Following this, the Baud Rate Gener-
ator is reloaded with the contents of SSPADD<7:0>
and resumes its count. When the Baud Rate Generator
times out (T
will be automatically cleared by hardware; the Baud
Rate Generator is suspended, leaving the SDA line
held low and the Start condition is complete.
FIGURE 15-19:
 2010 Microchip Technology Inc.
BRG
I
CONDITION TIMING
BRG
2
is
C MASTER MODE START
), the SEN bit of the SSPCON2 register
), the SDA pin is driven low. The action
reloaded
Write to SEN bit occurs here
FIRST START BIT TIMING
with
SDA
SCL
the
contents
SDA = 1,
SCL = 1
T
BRG
Preliminary
of
Set S bit (SSPSTAT<3>)
T
S
BRG
At completion of Start bit,
hardware clears SEN bit
15.3.8.1
If the user writes the SSPBUF when a Start sequence
is in progress, the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
and sets SSPIF bit
Note:
Note:
T
Write to SSPBUF occurs here
BRG
PIC18F/LF1XK50
1st bit
If at the beginning of the Start condition,
the SDA and SCL pins are already sam-
pled low, or if during the Start condition,
the SCL line is sampled low before the
SDA line is driven low, a bus collision
occurs, the Bus Collision Interrupt Flag,
BCLIF, is set, the Start condition is aborted
and the I
state.
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the Start
condition is complete.
WCOL Status Flag
T
BRG
2
C module is reset into its Idle
2nd bit
DS41350E-page 169