PIC16C54-RC/SO Microchip Technology, PIC16C54-RC/SO Datasheet - Page 69

• Manufacturer Part Number: PIC16C54-RC/SO
• Description: IC MCU OTP 512X12 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C54-RC/SO

• Core Size: 8-Bit
• Program Memory Size: 768B (512 x 12)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 12
• Program Memory Type: OTP
• Ram Size: 25 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6.25 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-SOIC (7.5mm Width)
• Controller Family/series: PIC16C
• No. Of I/o's: 12
• Ram Memory Size: 25Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Digital Ic Case Style: SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MIL309-1075 - ADAPTER 18-SOIC TO 18-SOIC309-1011 - ADAPTER 18-SOIC TO 18-DIP309-1010 - ADAPTER 18-SOIC TO 18-DIPAC164002 - MODULE SKT PROMATEII 18/28SOIC
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

12.0
Absolute Maximum Ratings
Ambient Temperature under bias ..................................................................................................... –55°C to +125°C
Storage Temperature ....................................................................................................................... –65°C to +150°C
Voltage on V
Voltage on MCLR with respect to V
Voltage on all other pins with respect to V
Total power dissipation
Max. current out of V
Max. current into V
Max. current into an input pin (T0CKI only).................................................................................................... ±500 A
Input clamp current, I
Output clamp current, I
Max. output current sunk by any I/O pin ........................................................................................................... 25 mA
Max. output current sourced by any I/O pin ...................................................................................................... 20 mA
Max. output current sourced by a single I/O port (PORTA, B or C) .................................................................. 40 mA
Max. output current sunk by a single I/O port (PORTA, B or C)........................................................................ 50 mA
† NOTICE: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This
is a stress rating only and functional operation of the device at those or any other conditions above those indicated in
the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods
may affect device reliability.
Note 1: Voltage spikes below V
2002 Microchip Technology Inc.
2: Power Dissipation is calculated as follows: Pdis = V
ELECTRICAL CHARACTERISTICS - PIC16C54/55/56/57
Thus, a series resistor of 50 to 100
than pulling this pin directly to V
DD
with respect to V
DD
SS
IK
pin ................................................................................................................................ 100 mA
(2)
OK
(V
pin ............................................................................................................................. 150 mA
............................................................................................................................... 800 mW
I
(V
< 0 or V
O
(†)
< 0 or V
SS
I
SS
..........................................................................................................0V to +7.5V
SS
> V
(1)
O
at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.
DD
....................................................................................................0V to +14V
> V
SS
) .................................................................................................... ±20 mA
SS
DD
............................................................................–0.6V to (V
.
) ............................................................................................. ±20 mA
should be used when applying a “low” level to the MCLR pin rather
Preliminary
DD
x {I
DD
–
I
OH
} +
{(V
DD
– V
PIC16C5X
OH
) x I
OH
DS30453D-page 67
} + (V
DD
+ 0.6V)
OL
x I
OL
)