PIC16C716-20/P Microchip Technology, PIC16C716-20/P Datasheet - Page 77

• Manufacturer Part Number: PIC16C716-20/P
• Description: IC MCU OTP 2KX14 A/D PWM 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C716-20/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1059 - ADAPTER 18 ZIF BD W/18SO PLUGSDVA16XP180 - ADAPTER DEVICE FOR MPLAB-ICEAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -

12.1
© 2005 Microchip Technology Inc.
DC CHARACTERISTICS
D001
D001A
D002*
D003
D004*
D004A*
D005
D010
D013
D020
D021
D021B
D022*
D022A*
1A
Note1:
Param
No.
2:
3:
4:
5:
6:
7:
*
†
DC Characteristics: PIC16C712/716-04 (Commercial, Industrial, Extended)
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
This is the limit to which V
The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and
switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current
consumption.
The test conditions for all I
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
MCLR = V
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the
part in Sleep mode, with all I/O pins in high-impedance state and tied to V
For RC Osc mode, current through R
Ir = V
Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for
design guidance only. This is not tested.
The
I
This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will operate correctly to
this trip point.
V
V
V
S
V
I
I
F
DD
DD
PD
Sym.
DD
DR
POR
VDD
BOR
I
I
OSC
WDT
BOR
or I
DD
current is the additional current consumed when this peripheral is enabled. This current should be added to the base
PD
/2R
Supply Voltage
RAM Data Retention Voltage
V
nal Power-on Reset signal
V
Power-on Reset signal
Brown-out Reset
voltage trip point
Supply Current
Power-down Current
Module Differential Current
Watchdog Timer
Brown-out Reset
LP Oscillator Operating Frequency
RC Oscillator Operating Frequency
XT Oscillator Operating Frequency
HS Oscillator Operating Frequency
measurement.
DD
DD
DD
EXT
; WDT enabled/disabled as specified.
Start Voltage to ensure inter-
Rise Rate to ensure internal
(mA) with R
Characteristic
(2,5)
DD
DD
EXT
can be lowered without losing RAM data.
measurements in active operation mode are:
PIC16C712/716-20 (Commercial, Industrial, Extended)
(3,5)
in kOhm.
EXT
(6)
(1)
is not included. The current through the resistor can be estimated by the formula
Standard Operating Conditions (unless otherwise stated)
Operating temperature
V
Min.
TBD
0.05
3.65
4.0
4.5
BOR
—
—
—
—
—
—
—
—
—
—
0
0
0
0
*
Typ†
10.5
TBD
V
1.5
0.8
4.0
1.5
1.5
2.5
6.0
—
—
—
—
—
—
—
—
—
—
SS
Max.
4.35
200
200
5.5
5.5
5.5
2.5
8.0
42
16
19
19
20
20
—
—
—
—
4
4
Units
V/ms PWRT enabled (PWRTE bit clear)
MHz
MHz
MHz
KHz
mA
mA
DD
V
V
V
V
V
V
-40°C
-40°C
A
A
A
A
A
A
0°C
and V
PIC16C712/716
DD
XT, RC and LP osc mode
HS osc mode
BOR enabled
See section on Power-on Reset for details
PWRT disabled (PWRTE bit set)
See section on Power-on Reset for details
BODEN bit set
F
F
V
V
V
V
WDTE bit set, V
BODEN bit set, V
All temperatures
All temperatures
All temperatures
All temperatures
OSC
OSC
DD
DD
DD
DD
,
SS
= 4.0V, WDT enabled,-40 C to +85 C
= 4.0V, WDT disabled, 0 C to +70 C
= 4.0V, WDT disabled,-40 C to +85 C
= 4.0V, WDT disabled,-40 C to +125 C
T
T
T
.
= 4 MHz, V
= 20 MHz, V
A
A
A
+125°C
(7)
+70°C
+85°C
Conditions
DD
DD
DD
DD
= 4.0V
= 4.0V
= 5.0V
DS41106B-page 75
= 4.0V
for commercial
for industrial
for extended