PIC24HJ12GP201-I/SO Microchip Technology, PIC24HJ12GP201-I/SO Datasheet - Page 128

• Manufacturer Part Number: PIC24HJ12GP201-I/SO
• Description: IC PIC MCU FLASH 4KX24 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ12GP201-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 12KB (4K x 24)
• Package / Case: 18-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit or 6-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164339 - MODULE SKT FOR PM3 28SOIC
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24HJ12GP201/202
14.1
Configure the Output Compare modes by setting the
appropriate Output Compare Mode (OCM<2:0>) bits in
the Output Compare Control (OCxCON<2:0>) register.
Table 14-1 lists the different bit settings for the Output
Compare modes. Figure 14-2 illustrates the output
compare operation for various modes. The user
TABLE 14-1:
FIGURE 14-2:
DS70282D-page 126
OCM<2:0>
Continuous Pulse Mode
000
001
010
011
100
101
110
111
Active High One-Shot
Active Low One-Shot
(OCM = 110 or 111)
Delayed One-Shot
Output Compare Modes
(OCM = 011)
(OCM = 100)
Toggle Mode
(OCM = 101)
(OCM = 001)
(OCM = 010)
PWM Mode
Module Disabled
Active-Low One-Shot
Active-High One-Shot
Toggle Mode
Delayed One-Shot
Continuous Pulse mode
PWM mode without fault
protection
PWM mode with fault protection 0, if OCxR is zero
OUTPUT COMPARE MODES
TMRy
OUTPUT COMPARE OPERATION
OCxRS
OCxR
Mode
Output Compare
Mode enabled
Controlled by GPIO register
Current output is maintained
0, if OCxR is zero
1, if OCxR is non-zero
1, if OCxR is non-zero
Preliminary
OCx Pin Initial State
Timer is reset on
period match
0
1
0
0
application must disable the associated timer when
writing to the output compare control registers to avoid
malfunctions.
Note:
See Section 13. “Output Compare” in
the “PIC24H Family Reference Manual”
(DS70247) for OCxR and OCxRS register
restrictions.
OCx Rising edge
OCx Falling edge
OCx Rising and Falling edge
OCx Falling edge
OCx Falling edge
No interrupt
OCFA Falling edge for OC1 to OC4
OCx Interrupt Generation
© 2009 Microchip Technology Inc.
—