PIC16F872-I/SS Microchip Technology, PIC16F872-I/SS Datasheet - Page 55

• Manufacturer Part Number: PIC16F872-I/SS
• Description: IC MCU FLASH 2KX14 EE 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F872-I/SS

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC16F
• No. Of I/o's: 22
• Eeprom Memory Size: 64Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: I2C, SPI, SSP
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 3 bit
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164307 - MODULE SKT FOR PM3 28SSOPAC164020 - MODULE SKT PROMATEII 44TQFPXLT28SS-1 - SOCKET TRANSITION ICE 28SSOP
• Lead Free Status / Rohs Status: Details

REGISTER 9-2:
© 2006 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3-0
SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS: 14h)
bit 7
WCOL: Write Collision Detect bit
Master mode:
1 = A write to SSPBUF was attempted while the I
0 = No collision
Slave mode:
1 = SSPBUF register is written while still transmitting the previous word (must be cleared in software)
0 = No collision
In SPI mode:
1 = A new byte is received while SSPBUF holds previous data. Data in SSPSR is lost on overflow.
0 = No overflow
In I
1 = A byte is received while the SSPBUF is holding the previous byte. SSPOV is a "don’t care" in
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In SPI mode:
When enabled, these pins must be properly configured as input or output.
1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In I
When enabled, these pins must be properly configured as input or output.
1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: Clock Polarity Select bit
In SPI mode:
1 = IDLE state for clock is a high level
0 = IDLE state for clock is a low level
In I
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch). (Used to ensure data setup time.)
In I
Unused in this mode
0000 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0010 = SPI Master mode, clock = F
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled.
0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
0110 = I
0111 = I
1000 = I
1011 = I
1110 = I
1111 = I
1001, 1010, 1100, 1101 = reserved
Legend:
R = Readable bit
- n = Value at POR
SSPOV: Receive Overflow Indicator bit
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
WCOL
R/W-0
2
2
2
2
In Slave mode, the user must read the SSPBUF, even if only transmitting data, to avoid over-
flows. In Master mode, the overflow bit is not set since each operation is initiated by writing to
the SSPBUF register. (Must be cleared in software.)
C mode:
Transmit mode. (Must be cleared in software.)
C mode:
C slave mode:
C master mode:
enabled
enabled
2
2
2
2
2
2
C Slave mode, 7-bit address
C Slave mode, 10-bit address
C Master mode, clock = F
C Firmware Controlled Master mode (slave idle)
C Firmware Controlled Master mode, 7-bit address with START and STOP bit interrupts
C Firmware Controlled Master mode, 10-bit address with START and STOP bit interrupts
SSPOV
R/W-0
W = Writable bit
’1’ = Bit is set
SSPEN
R/W-0
OSC
OSC
OSC
OSC
R/W-0
/4
/16
/64
/ (4 * (SSPADD+1)
CKP
2
C conditions were not valid
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
SSPM3
R/W-0
SSPM2
R/W-0
PIC16F872
x = Bit is unknown
SSPM1
R/W-0
DS30221C-page 53
SSPM0
R/W-0
bit 0