PIC16F84A-20/SO Microchip Technology, PIC16F84A-20/SO Datasheet - Page 153

• Manufacturer Part Number: PIC16F84A-20/SO
• Description: IC MCU FLASH 1KX14 EE 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F84A-20/SO

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 13
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 68 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-SOIC (7.5mm Width)
• Controller Family/series: PIC16F
• No. Of I/o's: 13
• Eeprom Memory Size: 64Byte
• Ram Memory Size: 68Byte
• Cpu Speed: 20MHz
• No. Of Timers: 1
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 68 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILI3-DB16F84A - BOARD DAUGHTER ICEPIC3309-1075 - ADAPTER 18-SOIC TO 18-SOIC309-1011 - ADAPTER 18-SOIC TO 18-DIP309-1010 - ADAPTER 18-SOIC TO 18-DIPAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

9.9
1997 Microchip Technology Inc.
GPIO and the TRISGP Register
GPIO is an 8-bit I/O register. Only the low order six bits are implemented (GP5:GP0). Bits 7 and
6 are unimplemented and read as ‘0’s. Any GPIO pin (except GP3) can be programmed
individually as input or output. The GP3 pin is an input only pin.
The TRISGP register controls the data direction for GPIO pins. A ‘1’ in a TRISGP register bit
puts the corresponding output driver in a hi-impedance mode. A ‘0’ puts the contents of the
output data latch on the selected pins, enabling the output buffer. The exceptions are GP3 which
is input only and its TRIS bit will always read as '1'. Upon reset, the TRISGP register is all ‘1’s,
making all pins inputs.
A read of the GPIO port, reads the pins not the output data latches. Any input must be present
until read by an input instruction (e.g., MOVF GPIO,W). The outputs are latched and remain
unchanged until the output latch is rewritten.
Example 9-8: Initializing GPIO
Figure 9-11: Block Diagram of GP5:GP0 Pins
The configuration word can set several I/O’s to alternate functions. When acting as alternate
functions the pins will read as ‘0’ during port read. The GP0, GP1, and GP3 pins can be config-
ured with weak pull-ups and also with interrupt on change. The interrupt on change and weak
pull-up functions are not pin selectable. Interrupt on change is enabled by setting INTCON<3>.
If the device configuration bits select one of the external oscillator modes, the GP4 and GP5 pin’s
GPIO functions are overridden and these pins are used for the oscillator.
CLRF
CLRF
BSF
MOVLW
MOVWF
Note 1: I/O pins have protection diodes to V
GP3 is input only with no data latch and no output drivers.
STATUS
GPIO
STATUS, RP0
0xCF
TRISGP
Data
Bus
WR
Port
W
Reg
TRIS ‘f’
; Bank0
; Initialize GPIO by clearing output
;
; Select Bank1
; Value used to initialize data direction
; GP<3:0> = inputs GP<5:4> = outputs
;
D
D
CK
CK
Reset
TRIS
Latch
Data
Latch
data latches
TRISGP<7:6> always read as '0'
Q
Q
Q
Q
RD Port
Section 9. I/O Ports
DD
and V
SS
.
V
V
P
N
SS
DD
I/O
pin
(1)
DS31009A-page 9-13
9