PIC18F2510-I/ML Microchip Technology, PIC18F2510-I/ML Datasheet - Page 8

• Manufacturer Part Number: PIC18F2510-I/ML
• Description: IC PIC MCU FLASH 16KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2510-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

PIC18F2410/2510/4410/4510
21. Module: A/D
TABLE 2:
22. Module: BOR
TABLE 3:
DS80277C-page 8
D005
A06A
A06
Param
Param
No.
No.
The A/D offset is greater than the specified limit in
Table 25-24 of the Device Data Sheet. The
updated conditions and limits are shown in bold
text in Table 2.
Work around
Three work arounds exist.
1. Configure the A/D to use the V
2. Perform a conversion on a known voltage
3. Increase system clock speed to 40 MHz and
Date Codes that pertain to this issue:
All engineering and production devices.
The BOR module may reset below the minimum
operating voltage of the device when configured
for BORV1:BORV0 = 11. The updated Reset
voltage specifications are shown in bold in
Table 3.
Work around
Use the next higher BOR voltage setting to ensure
a low V
Date Codes that pertain to this issue:
All engineering and production devices.
V
pins for the voltage references. This is done by
setting the VCFG<1:0> bits (ADCON1<5:4>).
reference voltage and adjust the A/D result in
software.
adjust A/D settings accordingly. Higher system
clock frequencies decrease offset error.
Sym
Symbol
E
E
BOR
OFF
OFF
DD
Brown-out Reset Voltage
PIC18LF2525/2620/4525/4620
BORV1:BORV0 =
A/D CONVERTER CHARACTERISTICS: PIC18F2410/2510/4410/4510 (INDUSTRIAL)
is detected above 2.0V.
BROWN-OUT RESET VOLTAGE
Characteristic
Offset Error
Offset Error
Characteristic
11
Min Typ Max Unit
N/A 2.05 N/A
REF
+ and V
REF
V
Min
—
—
-
23. Module: EUSART
24. Module: EUSART
Typ
—
—
The EUSART auto-baud feature may periodically
measure the incoming baud rate incorrectly. The
rate of incorrect baud rate measurements will
depend on the frequency of the incoming
synchronization byte and the system clock
frequency.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode (SYNC = 1) with clock
polarity high (SCKP = 1), the EUSART transmits a
shorter than expected clock on the CK pin for bit 0.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
<±2.0
<±3.5
Max
Units
LSb
LSb
© 2007 Microchip Technology Inc.
V
V
REF
REF
= V
= V
Conditions
REF
SS
and V
+ and V
DD
REF
-