PIC16F84A-20I/SS Microchip Technology, PIC16F84A-20I/SS Datasheet - Page 262

• Manufacturer Part Number: PIC16F84A-20I/SS
• Description: IC MCU FLASH 1KX14 EE 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F84A-20I/SS

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 13
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 68 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SSOP
• Controller Family/series: PIC16F
• No. Of I/o's: 13
• Eeprom Memory Size: 64Byte
• Ram Memory Size: 68Byte
• Cpu Speed: 20MHz
• No. Of Timers: 1
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 68 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• Data Rom Size: 64 B
• Height: 1.75 mm
• Length: 7.2 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 5.3 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SS1-1 - SOCKET TRANSITION 20DIP 20SSOPI3-DB16F84A - BOARD DAUGHTER ICEPIC3AC164307 - MODULE SKT FOR PM3 28SSOPAC164018 - MODULE SKT PROMATEII 20SSOP
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
16.3.6
DS31016A-page 16-12
SCK
(CKP = 0)
SCK
(CKP = 1)
SS
SSPIF
SDO
SDI
Slave Select Mode
The SS pin allows a synchronous slave mode. The SPI must be in slave mode
(SSPCON<3:0> = 04h) and the TRIS bit must be set the for the synchronous slave mode to be
enabled. When the SS pin is low, transmission and reception are enabled and the SDO pin is
driven. When the SS pin goes high, the SDO pin is no longer driven, even if in the middle of a
transmitted byte, and becomes a floating output. If the SS pin is taken low without resetting SPI
mode, the transmission will continue from the point at which it was taken high. To clear the bit
counter the Basic SSP module must be disabled and then re-enabled. External pull-up/pull-down
resistors may be desirable, depending on the application.
To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the
SPI needs to operate as a receiver the SDO pin can be configured as an input. This disables
transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot
create a bus conflict.
Figure 16-5: SPI Mode Waveform (Slave Mode with ss Control)
bit7
bit7
bit6
bit5
bit4
bit3
bit2
Next Q4 Cycle
after Q2
1997 Microchip Technology Inc.
bit1
bit0
bit0