PIC18F2550-I/SP Microchip Technology, PIC18F2550-I/SP Datasheet - Page 17

• Manufacturer Part Number: PIC18F2550-I/SP
• Description: IC PIC MCU FLASH 16KX16 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2550-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: SPI, I2C, EAUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163025, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4550 - BOARD DAUGHTER ICEPIC3DM163025 - PIC DEM FULL SPEED USB DEMO BRDDVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

39. Module: MSSP (I
EXAMPLE 9:
© 2009 Microchip Technology Inc.
;Initial conditions: SPEN = 0 (module disabled)
;To re-enable the module:
;Re-Initialize TXSTAx, BAUDCONx, SPBRGx, SPBRGHx registers (if needed)
;Re-Initialize RCSTAx register (if needed), but do not set SPEN = 1 yet
;Now enable the module, but add a 2-Tcy delay before executing any two-cycle
;instructions
bsf
nop
nop
;CPU may now execute 2 cycle instructions
When configured for I
MSSP module may not receive the correct data, in
extremely rare cases. This occurs only if the Serial
Receive/Transmit Buffer Register (SSPBUF) is not
read after the SSPIF interrupt (PIR1<3>) has
occurred, but before the first rising clock edge of
the next byte being received.
Work around
The issue can be resolved in either of these ways:
• Prior to the I
• Each time the SSPIF is set, read the SSPBUF
Affected Silicon Revisions
clock stretching feature.
This
(SSPCON2<0>).
before the first rising clock edge of the next byte
being received.
A3
X
RCSTA1, SPEN ;or RCSTA2 if EUSART2
;1 Tcy delay
;1 Tcy delay (two total)
is
done
B4
X
2
RE-ENABLING A EUSART MODULE
C slave reception, enable the
2
by
C™ Slave)
2
B5
X
C™ slave reception, the
setting
B6
X
the
SEN
PIC18F2455/2550/4455/4550
B7
X
bit
40. Module: MSSP (I
41. Module: EUSART
When in I
clock stretching, the first clock pulse after the slave
releases the SCL line may be narrower than the
configured clock width. This may result in the slave
missing the first clock in the next transmission/
reception.
Work around
The clock pulse will be the normal width if the slave
does not perform clock stretching.
Affected Silicon Revisions
In rare situations, when interrupts are enabled,
unexpected results may occur if:
• The EUSART is disabled (the SPEN bit,
• The EUSART is re-enabled (RCSTAx<7> = 1)
• A two-cycle instruction is executed immediately
Work around
Add a 2 T
enables the EUSART module (sets SPEN = 1).
See Example 9.
Affected Silicon Revisions
RCSTAx<7> = 0)
after setting SPEN = 1
A3
A3
2
CY
C Master mode, if the slave performs
B4
B4
X
delay after any instruction that re-
2
C™ Master)
B5
B5
X
DS80478A-page 17
B6
B6
X
X
B7
B7
X
X