PIC24FJ128GA010-I/PF Microchip Technology, PIC24FJ128GA010-I/PF Datasheet - Page 12

• Manufacturer Part Number: PIC24FJ128GA010-I/PF
• Description: IC PIC MCU FLASH 64KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ128GA010-I/PF

• Program Memory Type: FLASH
• Program Memory Size: 128KB (43K x 24)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 84
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Controller Family/series: PIC24
• No. Of I/o's: 84
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: EUART, I2C, PSP, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM240011 - KIT STARTER MPLAB FOR PIC24F MCUDV164033 - KIT START EXPLORER 16 MPLAB ICD2MA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164323 - MODULE SKT FOR 100TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FJXXXGA0XX
3.0
ICSP mode is a special programming protocol that
allows you to read and write to PIC24FJXXXGA0XX
device family memory. The ICSP mode is the most
direct method used to program the device; note, how-
ever, that Enhanced ICSP is faster. ICSP mode also
has the ability to read the contents of executive
memory to determine if the programming executive is
present. This capability is accomplished by applying
control codes and instructions, serially to the device,
using pins, PGCx and PGDx.
In ICSP mode, the system clock is taken from the
PGCx pin, regardless of the device’s oscillator Config-
uration bits. All instructions are shifted serially into an
internal buffer, then loaded into the Instruction Register
(IR) and executed. No program fetching occurs from
internal memory. Instructions are fed in 24 bits at a
time. PGDx is used to shift data in and PGCx is used
as both the serial shift clock and the CPU execution
clock.
3.1
Figure 3-1 shows the high-level overview of the
programming process. After entering ICSP mode, the
first action is to Chip Erase the device. Next, the code
memory is programmed, followed by the device
Configuration registers. Code memory (including the
Configuration registers) is then verified to ensure that
programming was successful. Then, program the
code-protect Configuration bits, if required.
DS39768D-page 12
Note:
DEVICE PROGRAMMING – ICSP
Overview of the Programming
Process
During ICSP operation, the operating
frequency of PGCx must not exceed
10 MHz.
FIGURE 3-1:
3.2
Upon entry into ICSP mode, the CPU is Idle. Execution
of the CPU is governed by an internal state machine. A
4-bit control code is clocked in using PGCx and PGDx,
and this control code is used to command the CPU (see
Table 3-1).
The SIX control code is used to send instructions to the
CPU for execution, and the REGOUT control code is
used to read data out of the device via the VISI register.
TABLE 3-1:
0000b
0001b
0010b-1111b N/A
Control Code
4-Bit
ICSP Operation
Program Configuration Bits
Verify Configuration Bits
SIX
REGOUT
Mnemonic
CPU CONTROL CODES IN
ICSP™ MODE
Program Memory
Verify Program
Enter ICSP™
Perform Chip
HIGH-LEVEL ICSP™
PROGRAMMING FLOW
Exit ICSP
© 2008 Microchip Technology Inc.
Erase
Done
Start
Shift in 24-bit instruction
and execute.
Shift out the VISI (0784h)
register.
Reserved.
Description