PIC18F452-I/PT Microchip Technology, PIC18F452-I/PT Datasheet - Page 2

• Manufacturer Part Number: PIC18F452-I/PT
• Description: IC MCU FLASH 16KX16 EE 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F452-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 34
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 34
• Interface Type: I2C/SPI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18FXX2
3. Module: MSSP (All I
DS80173C-page 2
The Buffer Full (BF) flag bit of the SSPSTAT
register (SSPSTAT<0>) may be inadvertently
cleared even when the SSPBUF register has not
been read. This will occur only when the following
two conditions occur simultaneously:
• The four Least Significant bits of the BSR
• Any instruction that contains C9h in its 8 Least
Work around
All work arounds will involve setting the contents of
BSR<3:0> to some value other than 0Fh.
In addition to those proposed below, other
solutions may exist.
1. When developing or modifying code, keep
2. If accessing a part of Bank 15 is required and
3. If pointing the BSR to Bank 15 is unavoidable,
Date Codes that pertain to this issue:
All engineering and production devices.
register are equal to 0Fh (BSR<3:0> = 1111)
and
Significant bits (i.e., register file addresses,
literal data, address offsets, etc.) is executed.
these guidelines in mind:
• Assign 12-bit addresses to all variables.
• Do not set the BSR to point to Bank 15
• Allow the assembler to manipulate the
the use of access banking is not possible,
consider using indirect addressing.
review the absolute file listing. Verify that no
instructions contain C9h in the 8 Least
Significant bits while the BSR points to Bank 15
(BSR = 0Fh).
This allows the assembler to know when
access banking can be used.
(BSR = 0Fh).
access bit present in most instructions.
Accessing the SFRs in Bank 15 will be done
through the Access Bank. Continue to use
the BSR to select all GPR Banks.
SPI™ Modes)
2
C™ and
4. Module: Core (Instruction Set)
EXAMPLE 1:
5. Module: Reset
MOVLW
ADDLW
BTFSC
INCFSZ byte2
DAW
BTFSC
INCFSZ byte2
This is repeated for each DAW instruction.
The Decimal Adjust W register instruction, DAW,
may improperly clear the Carry bit (STATUS<0>)
when executed.
Work around
Test the Carry bit state before executing the DAW
instruction. If the Carry bit is set, increment the
next higher byte to be added using an instruction
such as INCFSZ (this instruction does not affect
any Status flags and will not overflow a BCD nib-
ble). After the DAW instruction has been executed,
process the Carry bit normally (see Example 1).
It has been observed that in certain Reset condi-
tions, including power-up, the first GOTO instruction
at address 0x0000 may not be executed. This
occurrence is rare and affects very few applications.
To determine if your system is affected, test a
statistically significant number of applications across
the operating temperature, voltage and frequency
ranges of the application. Affected systems will
repeatably fail normal testing. Systems not affected
will continue to not be affected over time.
Work around
Insert a NOP instruction at address 0x0000.
Date Codes that pertain to this issue:
All engineering and production devices.
0x80
0x80
STATUS,C
STATUS,C
PROCESSING THE CARRY
BIT DURING BCD ADDITIONS
; .80 (BCD)
; .80 (BCD)
; test C
; inc next higher LSB
; test C
; inc next higher LSB
© 2005 Microchip Technology Inc.