PIC17C42A-25/P Microchip Technology, PIC17C42A-25/P Datasheet - Page 31

• Manufacturer Part Number: PIC17C42A-25/P
• Description: IC MCU OTP 2KX16 PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C42A-25/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: OTP
• Ram Size: 232 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: PIC17C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 232 B
• Interface Type: SCI, USART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Operating Supply Voltage: 2.5 V to 6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• For Use With: DVA17XP401 - DEVICE ADAPTER FOR PIC17C42AAC174001 - MODULE SKT PROMATEII 40DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

6.1.2
When either microprocessor or extended microcontrol-
ler mode is selected, PORTC, PORTD and PORTE are
configured as the system bus. PORTC and PORTD are
the multiplexed address/data bus and PORTE is for the
control signals. External components are needed to
demultiplex the address and data. This can be done as
shown in Figure 6-4. The waveforms of address and
data are shown in Figure 6-3. For complete timings,
please refer to the electrical specification section.
FIGURE 6-3:
The system bus requires that there is no bus conflict
(minimal leakage), so the output value (address) will be
capacitively held at the desired value.
As the speed of the processor increases, external
EPROM memory with faster access time must be used.
Table 6-2 lists external memory speed requirements for
a given PIC17C4X device frequency.
FIGURE 6-4:
<15:0>
1996 Microchip Technology Inc.
ALE
WR
OE
AD
Note 1: Use of I/O pins is only required for paged memory.
'1'
Q1
Address out Data in
EXTERNAL MEMORY INTERFACE
2: This signal is unused for ROM and EPROM devices.
PIC17C4X
Q2
Read cycle
AD15-AD8
AD7-AD0
Q3
EXTERNAL PROGRAM
MEMORY ACCESS
WAVEFORMS
TYPICAL EXTERNAL PROGRAM MEMORY CONNECTION DIAGRAM
I/O
ALE
WR
OE
(1)
Q4
Q1
Address out
Q2
Q3
Write cycle
Data out
Q4
AD15-AD0
Q1
373
373
A15-A0
In extended microcontroller mode, when the device is
executing out of internal memory, the control signals
will continue to be active. That is, they indicate the
action that is occurring in the internal memory. The
external memory access is ignored.
This following selection is for use with Microchip
EPROMs. For interfacing to other manufacturers mem-
ory, please refer to the electrical specifications of the
desired PIC17C4X device, as well as the desired mem-
ory device to ensure compatibility.
TABLE 6-2:
Note 1: The access times for this requires the use of
Frequency
PIC17C4X
Oscillator
Note:
16 MHz
20 MHz
25 MHz
33 MHz
138
8 MHz
(1)
fast SRAMS.
The external memory interface is not sup-
ported for the LC devices.
D7-D0
CE
OE
Ax-A0
Instruction
Memory
Time (T
(MSB)
500 ns
250 ns
200 ns
160 ns
121 ns
Cycle
WR
EPROM MEMORY ACCESS
TIME ORDERING SUFFIX
(2)
CY
)
PIC17C4X
PIC17C42
N.A.
N.A.
-25
-12
-90
EPROM Suffix
DS30412C-page 31
Ax-A0
D7-D0
CE
OE
Memory
(LSB)
PIC17C43
PIC17C44
WR
-25
-15
-10
-70
(1)
(2)