C8051F562-IQ Silicon Laboratories Inc, C8051F562-IQ Datasheet - Page 181

• Manufacturer Part Number: C8051F562-IQ
• Description: IC 8051 MCU 32K FLASH 32-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F56xr

Specifications of C8051F562-IQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-QFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), LIN, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 25x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Operating Supply Voltage: 1.8 V to 5.25 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F560DK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1691 - KIT DEVELOPMENT FOR C8051F560
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1698

19.6. Special Function Registers for Accessing and Configuring Port I/O
All Port I/O are accessed through corresponding special function registers (SFRs) that are both byte
addressable and bit addressable, except for P4 which is only byte addressable. When writing to a Port, the
value written to the SFR is latched to maintain the output data value at each pin. When reading, the logic
levels of the Port's input pins are returned regardless of the XBRn settings (i.e., even when the pin is
assigned to another signal by the Crossbar, the Port register can always read its corresponding Port I/O
pin). The exception to this is the execution of the read-modify-write instructions that target a Port Latch reg-
ister as the destination. The read-modify-write instructions when operating on a Port SFR are the following:
ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ and MOV, CLR or SETB, when the destination is an individ-
ual bit in a Port SFR. For these instructions, the value of the latch register (not the pin) is read, modified,
and written back to the SFR.
Ports 0–3 have a corresponding PnSKIP register which allows its individual Port pins to be assigned to dig-
ital functions or skipped by the Crossbar. All Port pins used for analog functions, GPIO, or dedicated digital
functions such as the EMIF should have their PnSKIP bit set to 1.
The Port input mode of the I/O pins is defined using the Port Input Mode registers (PnMDIN). Each Port
cell can be configured for analog or digital I/O. This selection is required even for the digital resources
selected in the XBRn registers, and is not automatic. The only exception to this is P4, which can only be
used for digital I/O.
The output driver characteristics of the I/O pins are defined using the Port Output Mode registers (PnMD-
OUT). Each Port Output driver can be configured as either open drain or push-pull. This selection is
required even for the digital resources selected in the XBRn registers, and is not automatic. The only
exception to this is the SMBus (SDA, SCL) pins, which are configured as open-drain regardless of the
PnMDOUT settings.
SFR Definition 19.12. P0: Port 0
SFR Address = 0x80; SFR Page = All Pages; Bit-Addressable
Name
Reset
Bit
7:0
Type
Bit
P0[7:0]
Name
7
1
Port 0 Data.
Sets the Port latch logic
value or reads the Port pin
logic state in Port cells con-
figured for digital I/O.
6
1
Description
5
1
Rev. 1.1
0: Set output latch to logic
LOW.
1: Set output latch to logic
HIGH.
4
1
P0[7:0]
R/W
Write
3
1
C8051F55x/56x/57x
2
1
0: P0.n Port pin is logic
LOW.
1: P0.n Port pin is logic
HIGH.
1
1
Read
0
1
181