PIC12HV609-I/P Microchip Technology, PIC12HV609-I/P Datasheet - Page 106

• Manufacturer Part Number: PIC12HV609-I/P
• Description: IC PIC MCU FLASH 1KX14 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12HV609-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 5
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS-232 / USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162083 - HEADER MPLAB ICD2 PIC16F616 8/14AC162058 - HEADER MPLAB ICD2 FOR PIC12F683AC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12F609/615/12HV609/615
11.4.2
An overflow (FFh
the T0IF bit of the INTCON register. The interrupt can
be enabled/disabled by setting/clearing T0IE bit of the
INTCON register. See Section 5.0 “Timer0 Module”
for operation of the Timer0 module.
FIGURE 11-7:
DS41302A-page 104
(615 only)
(615 only)
(615 only)
TIMER0 INTERRUPT
IOC-GP0
IOC-GP1
IOC-GP2
IOC-GP3
IOC-GP4
IOC-GP5
TMR2IF
TMR2IE
TMR1IE
TMR1IF
CCP1IF
CCP1IE
IOC0
IOC1
IOC2
IOC3
IOC4
IOC5
ADIF
ADIE
CMIF
CMIE
00h) in the TMR0 register will set
INTERRUPT LOGIC
Note 1:
GPIE
Preliminary
GPIF
INTF
INTE
PEIE
T0IF
T0IE
GIE
Some peripherals depend upon the system clock for
operation. Since the system clock is suspended during Sleep, only
those peripherals which do not depend upon the system clock will wake
the part from Sleep. See Section 11.7.1 “Wake-up from Sleep”.
11.4.3
An input change on GPIO sets the GPIF bit of the
INTCON register. The interrupt can be enabled/
disabled by setting/clearing the GPIE bit of the
INTCON register. Plus, individual pins can be
configured through the IOC register.
Note:
GPIO INTERRUPT-ON-CHANGE
If a change on the I/O pin should occur
when any GPIO operation is being
executed, then the GPIF interrupt flag may
not get set.
Wake-up (If in Sleep mode)
© 2006 Microchip Technology Inc.
Interrupt to CPU
(1)