C8051F346-GM Silicon Laboratories Inc, C8051F346-GM Datasheet - Page 142

• Manufacturer Part Number: C8051F346-GM
• Description: IC 8051 MCU 64K FLASH MEM 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F346-GM

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4352 B
• Interface Type: I2C, SPI, UART
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X770-1006 - ISP 4PORT FOR SILABS C8051F MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1347-5

C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
15. Port Input/Output
Digital and analog resources are available through 40 I/O pins (48-pin packages) or 25 I/O pins (32-pin
packages). Port pins are organized as shown in Figure 15.1. Each of the Port pins can be defined as gen-
eral-purpose I/O (GPIO) or analog input; Port pins P0.0-P3.7 can be assigned to one of the internal digital
resources as shown in Figure 15.3. The designer has complete control over which functions are assigned,
limited only by the number of physical I/O pins. This resource assignment flexibility is achieved through the
use of a Priority Crossbar Decoder. Note that the state of a Port I/O pin can always be read in the corre-
sponding Port latch, regardless of the Crossbar settings.
The Crossbar assigns the selected internal digital resources to the I/O pins based on the Priority Decoder
(Figure 15.3 and Figure 15.4). The registers XBR0, XBR1, and XBR2 defined in SFR Definition 15.1, SFR
Definition 15.2, and SFR Definition 15.3, are used to select internal digital functions.
All Port I/Os are 5 V tolerant (refer to Figure 15.2 for the Port cell circuit). The Port I/O cells are configured
as either push-pull or open-drain in the Port Output Mode registers (PnMDOUT, where n = 0,1,2,3,4). Com-
plete Electrical Specifications for Port I/O are given in Table 15.1 on page 158.
142
Figure 15.1. Port I/O Functional Block Diagram (Port 0 through Port 3)
Highest
Priority
Lowest
Priority
SYSCLK
UART1**
Outputs
Outputs
UART0
SMBus
T0, T1
P0
P1
P2
P3
PCA
CP0
CP1
SPI
(P3.0-P3.7*)
(P0.0-P0.7)
(P1.0-P1.7)
(P2.0-P2.7)
2
4
2
2
2
6
2
2
8
8
8
8
Rev. 1.3
XBR0, XBR1, XBR2,
PnSKIP Registers
Crossbar
Decoder
Priority
Digital
8
8
8
8
PnMDIN Registers
*P3.1-P3.7 only available on 48-pin
packages
**UART1 only available on
C8051F340/1/4/5/8/A/B devices
PnMDOUT,
Cells
Cells
Cells
Cells
I/O
I/O
I/O
I/O
P0
P1
P2
P3
P0.0
P0.7
P1.0
P1.7
P2.0
P2.7
P3.0
P3.7*